Manual Makita 6841R (page 6 of 36) (English, German, Polish)

690977

Zoom out

Zoom in

1/36

Fig.5

Setting for desired screw length

Fig.6

There are 3 positive-lock screw length settings. To obtain

the desired setting, pull out the stopper base while

depressing the lever until you see the number of the

desired screw length (indicated on the plate) appear to

rest on the very top edge of the casing. See the table

below for the relation between the number indicated on

the plate and the respective screw length ranges.

25/28 25 mm - 28 mm

32 28 mm - 35 mm

41 35 mm - 41 mm

Number indicated on the plate

Screw length range

009832

Adjusting the driving depth

Fig.7

Depress the stopper base as far as it will go. While

keeping it in this position, turn the adjusting knob until the

bit tip projects approx. 5 mm from the stopper base. Drive

a trial screw. If the screw head projects above the surface

of the workpiece, turn the adjusting knob in the "A"

direction; if the screw head is counter-sunk, turn the

adjusting knob in the "B" direction.

Installing screw strip

1. Squeeze the lock lever with fingers and open the

magazine cap.

Fig.8

Roll up the screw strip in a form of coil

counterclockwise and place it inside the magazine.

Fig.9

3. Run the end of the screw strip on the slotted

passage starting from above the magazine.

Fig.10

4. Close the magazine cap while squeezing the lock

lever with fingers.

Fig.11

5. Insert the top end of the screw strip into the portion

A of the feeder box and feed it in the direction of

the arrow.

Fig.12

6. Set the screw strip so that the first screw of the

strip seats with a space for one screw left before

the screw-driving position.

Fig.13

Removing the screw strip

When removing the screw strip at or before using up the

screws, pull it out in the direction of the arrow.

Fig.14

If you set the reverse lever as shown in the figure, you

can pull out the screw strip in the reverse direction of the

arrow.

Fig.15

Pulling away the screw strip

Fig.16

While operating the tool with the screw strip, the used

strip comes out. as shown in the figure.

Hook a hole in the strip on the protrusion (A ) and then

pull away the used strip that has come out in the direction

of arrow.

Extension handle (optional accessory)

Fig.17

Use of extension handle allows you to drive screws into

floors while standing.

OPERATION

Driving operation

Fig.18

Switch on the tool by pressing the switch trigger and at

the same time pushing the lock button. Hold the tool

squarely against the workpiece and apply forward

pressure to the tool. The screw will be automatically

carried to the driving position and driven into the

workpiece.

NOTE:

• Do not fire the tool without screws. This will

damage the workpiece.

• Do not apply oil or grease on the sliding surface of

the feeder box.

MAINTENANCE

CAUTION:

• Always be sure that the tool is switched off and

unplugged before attempting to perform inspection

or maintenance.

• Never use gasoline, benzine, thinner, alcohol or the

like. Discoloration, deformation or cracks may

result.

Replacing carbon brushes

Fig.19

Remove and check the carbon brushes regularly.

Replace when they wear down to the limit mark. Keep

the carbon brushes clean and free to slip in the holders.

Both carbon brushes should be replaced at the same

time. Use only identical carbon brushes.

Use a screwdriver to remove the brush holder caps. Take

out the worn carbon brushes, insert the new ones and

secure the brush holder caps.

Fig.20

To maintain product SAFETY and RELIABILITY, repairs,

any other maintenance or adjustment should be

performed by Makita Authorized Service Centers, always

using Makita replacement parts.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita 6841R in the language / languages: English, German, Polish as an attachment in your email.

The manual is 1,6 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita 6841R Manual

Product: