Manual Makita 6835dwde (page 5 of 14) (English, Dutch)

381158

Zoom out

Zoom in

1/14

OPERATING INSTRUCTIONS

Installing or removing battery cartridge (Fig. 1)

• Always switch off the tool before insertion or removal of

the battery cartridge.

• To remove the battery cartridge, withdraw it from the

tool while pressing the push buttons on both sides of

the cartridge.

• To insert the battery cartridge, align the tongue on the

battery cartridge with the groove in the housing and slip

it into place. Always insert it all the way until it locks in

place with a little click. If not, it may accidentally fall out

of the tool, causing injury to you or someone around

you.

• Do not use force when inserting the battery cartridge. If

the cartridge does not slide in easily, it is not being

inserted correctly.

Setting for desired screw length (Fig. 2)

There are 3 positive-lock screw length settings. To obtain

the desired setting, pull out the stopper base while

depressing the lever until you see the number of the

desired screw length (indicated on the plate) appear to

rest on the very top edge of the casing. See the table

below for the relation between the number indicated on

the plate and the respective screw length ranges.

Adjusting the driving depth (Fig. 3)

Depress the stopper base as far as it will go. While keep-

ing it in this position, turn the adjusting knob until the bit

tip projects approx. 5 mm from the stopper base. Drive a

trial screw. If the screw head projects above the driving

surface, turn the adjusting knob in the A direction; if the

screw head is countersunk, turn the adjusting knob in the

B direction.

Installing screw strip (Fig. 4 & 5)

Insert the screw strip through the screw guide. Then

insert it through the feeder box until the first screw

reaches the position next to the driving position.

Removing screw strip (Fig. 6 & 7)

To remove the screw strip, just pull it out in the direction

of the arrow. If you depress the reverse button, you can

pull out the screw strip in the reverse direction of the

arrow.

Carry hook (Fig. 8)

The carry hook is convenient for temporarily hooking the

tool. It can be installed on either side of the tool. When

installing or removing the carry hook, widen it by pressing

its lower portion in the direction of the arrow.

Switch action (Fig. 9)

CAUTION:

Before inserting the battery cartridge into the tool, always

check to see that the switch trigger actuates properly and

returns to the “OFF” position when released.

To start the tool, simply pull the trigger. Release the trig-

ger to stop.

Driving operation (Fig. 10)

Switch on the tool by pulling the switch trigger. Hold the

tool squarely and firmly up against the driving surface. A

screw will be automatically carried to the driving position

and fastened.

CAUTION:

• Always check the bit carefully for wear before driving

operations. Replace a worn bit or poor fastening may

result.

• Always hold the tool squarely against the driving sur-

face. Holding it at an angle may damage the screw

heads and cause wear on the bit. This may also lead to

poor fastening.

• Always keep the tool firmly against the driving surface

until the driving is over. Failure to do so may cause

insufficient fastening of screws.

• Be careful not to drive a screw onto another screw

already fastened.

• Do not operate the tool without screws. It will damage

the driving surface.

• If the feeder box does not work smoothly when driving

screws, spray car wax (spray type) on the sliding sur-

faces. Never lubricate it.

Driving in corner (Fig. 11)

This tool can be used to drive at a position 15 mm away

from the wall as shown in Fig. 11.

CAUTION:

Driving at a position closer than 15 mm to the wall or

driving with the stopper base in contact with the wall may

damage the screw heads and cause wear on the bit. This

may also lead to poor fastening of screws and malfunc-

tion of the tool.

Installing or removing bit (Fig. 12 & 13)

Important:

Always be sure that the tool is switched off and the bat-

tery cartridge is removed before installing or removing

the bit.

Loosen the thumb screws which secure the casing. Pull

out the casing in the direction of the arrow. Press the dust

cover toward the plain bearing and pull out the bit. If the

dust cover cannot be moved as far as the plain bearing,

try it again after turning the bit slightly. To install the bit,

insert it into the socket while turning it slightly. After

installing, always make sure that the bit is securely held

in place by trying to pull it out.

Number indicated

on the plate

Screw length range

(mm)

25/28 25 – 28

32 28 – 5

40 35 – 41

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita 6835dwde in the language / languages: English, Dutch as an attachment in your email.

The manual is 0,21 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita 6835dwde Manual

Product: