690971

Makita 6723DW Manual

10
Zoom out
Zoom in
Previous page
1/104
Next page
10
6. Using the screwdriver
When using the screwdriver the following points should be observed.
1. Place the point of the screwdriver bit in the head of the screw and apply light pressure to the
screwdriver.
2. Make sure that the screwdriver bit is inserted straight and upright in the screw head, or the
screw may be damaged.
3. Start the screwdriver by pressing the On/Off switch.
4. When driving wood screws, pre-drill pilot holes to make driving easier and to prevent splitting
the material.
5. The pilot hole has two purposes. It acts as a guide for the screw to follow and it prevents
distortion or splitting of the wood.
6. Pilot holes should be drilled to a depth equal to or greater than the length of the screw to be
used.
7. The table below should be used as a guide for the size of the pilot hole.
8. Select forward rotation to drive screws in and reverse rotation to take them out.
9. Take care not to overtighten small brass screws. The screw head is easily twisted off and the
threads can strip. Hand tightening of these screws is recommended.
10. Use Posidrive screws whenever possible. They are easier to drive, as the screwdriver bit
engages more firmly in the screw head.
11. When inserting a screw into a hole that is already threaded, start the screw by hand. Run the
screw until you feel the threads catch and then use the screwdriver to tighten the screw.
12. When using the nut drivers supplied with this screwdriver, take care not to overtighten the
nuts as they could be damaged.
CLEANING AND MAINTENANCE
WARNING!
Do not press the On/Off switch when performing cleaning and
maintenance procedures.
After use, remove the screwdriver bit and tap the side of the screwdriver bit holder to remove any
dust, or chippings etc.
Clean the body of the screwdriver with a soft cloth. Keep the handle clean and free from oil and
grease.
Keep the charging adaptor clean and free from dust and grease. Worn or damaged parts must be
replaced by qualified personnel. There are no user servicable parts inside the screwdriver. Refer
to qualified service personnel if internal maintenance is required. Always store the screwdriver
and the charging adaptor in the carrying case.
Pilot hole diameter
Screw size Soft wood Hard wood
No. 6 (3.5 mm) 2.0 mm 2.5 mm
No. 8 (4.0 mm) 3.2 mm 3.5 mm
No.10 (5.0 mm) 3.5 mm 4.0 mm
… 10 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Makita 6723DW at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Makita 6723DW in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 1,59 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info