Manual Makita 6705D (page 4 of 7) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish)

448223

Zoom out

Zoom in

1/7

Installing or removing bit (Fig. 2 & 3)

Important:

Always be sure that the tool is switched off and the bat-

tery cartridge is removed before installing or removing

the bit.

Use only the driver bit or socket bit shown in Fig. 2.

Do not use any other driver bit or socket bit.

To install the bit, pull the sleeve in the direction of the

arrow and insert the bit into the sleeve as far as it will go.

Then release the sleeve to secure the bit.

To remove the bit, pull the sleeve in the direction of the

arrow and pull the bit out firmly.

Switch action (Fig. 4)

CAUTION:

Before inserting the battery cartridge into the tool, always

check to see that the switch trigger actuates properly and

returns to the “OFF” position when released.

To start the tool, simply pull the trigger. Release the trig-

ger to stop.

Reversing switch action (Fig. 4)

CAUTION:

• Always check the direction of rotation before operation.

• Use the reversing switch only after the tool comes to a

complete stop. Changing the direction of rotation

before the tool stops may damage the tool.

This tool has a reversing switch to change the direction of

rotation. Slide the reversing switch up for clockwise rota-

tion or slide it down for counterclockwise rotation.

Overload protector

The overload protector automatically cuts out to break

the circuit whenever heavy work is prolonged. Wait 20 –

30 seconds before resuming operation.

Adjusting the fastening torque (Fig. 5)

The fastening torque can be adjusted infinitely from

approx. 5 kg•cm to 37 kg•cm. To adjust it, loosen the two

screws and turn the adjusting ring. Then tighten the

screws to secure the adjusting ring. Refer to the table

below for relation between the numbers on the adjusting

ring and the fastening torque to be obtained.

(Example)

10 kg•cm of fastening torque can be obtained when the

number 2 is aligned to the red mark.

NOTE:

• Always tighten the two screws to secure the adjusting

ring after adjusting the fastening torque.

• The fastening torque may differ depending upon the

kind of screws, the type of materials to be fastened,

etc. Before starting your job, always perform a test

operation to verify the adequate fastening torque.

Operation

The proper fastening torque may differ depending upon

the kind or size of screws, the type of materials to be fas-

tened, the condition of the threads, etc. Before starting

your job, always perform a test operation to verify ade-

quate fastening torque.

As soon as the screw becomes tight, the clutch will cut in

and the motor will stop automatically. Release the switch

trigger.

NOTE:

• Make sure that the driver bit is inserted straight in the

screw head, or the screw and/or bit may be damaged.

• If the motor will not start even after you pull the trigger,

release the trigger. Then pull the trigger again after

turning the socket slightly with your fingers.

MAINTENANCE

CAUTION:

Always be sure that the tool is switched off and the bat-

tery cartridge is removed before carrying out any work on

the tool.

To maintain product safety and reliability, repairs, mainte-

nance or adjustment should be carried out by a Makita

Authorized Service Center.

ACCESSORIES

CAUTION:

These accessories or attachments are recommended for

use with your Makita tool specified in this manual. The

use of any other accessories or attachments might

present a risk of injury to persons. Only use accessory or

attachment for its stated purpose.

If you need any assistance for more details regarding

these accessories, ask your local Makita service center.

• Various type of Makita genuine batteries and chargers

• Plastic carrying case

Numbers on

adjusting ring

Fastening torque to

be obtained

1 5 kg•cm

210kg•cm

318kg•cm

427kg•cm

537kg•cm

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita 6705D in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 0,13 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita 6705D Manual

Product: