382487

Makita 5705r Manual

6
Zoom out
Zoom in
Previous page
1/13
Next page
Don’t support board or panel away from the cut.
Fig. B
9. Use Rip Fence.
Always use a fence or straight edge guide
when ripping.
10. Guard Against Kickback. (Fig. A & C)
Kickback occurs when the saw stalls rapidly
and is driven back towards the operator.
Release switch immediately if blade binds or
saw stalls. Keep blades sharp. Support large
panels as shown in Fig. A. Use fence or
straight edge guide when ripping. Don’t force
tool. Stay alert-exercise control. Don’t remove
saw from work during a cut while the blade is
moving.
NEVER place your hand or fingers behind the
saw. If kickback occurs, the saw could easily
jump backwards over your hand, possibly
causing severe injury.
Fig. C
11. Lower Guard. Raise lower guard with the
retracting handle.
12. Adjustments. Before cutting be sure depth
and bevel adjustments are tight.
13. Use Only Correct Blades In Mounting. Don’t
use blades with incorrect size holes. Never
use defective or incorrect blade washers or
bolts.
14. Avoid Cutting Nails. Inspect for and remove all
nails from lumber before cutting.
15. When operating the saw, keep the cord away
from the cutting area and position it so that it
will not be caught on the workpiece during the
cutting operation.
Operate with proper hand support, proper
workpiece support, and supply cord routing
away from the work area.
WARNING:
It is important to support the workpiece prop-
erly and to hold the saw firmly to prevent loss
of control which could cause personal injury.
Fig. D illustrates typical hand support of the
saw.
A typical illustration of proper hand support,
workpiece support, and supply cord routing.
Fig. D
16. Place the wider portion of the saw base on that
part of the workpiece which is solidly sup-
ported, not on the section that will fall off when
the cut is made.
As examples, Fig. E illustrates the RIGHT way
to cut off the end of a board, and Fig. F the
WRONG way. If the workpiece is short or
small, clamp it down. DON’T TRY TO HOLD
SHORT PIECES BY HAND! (Fig. F)
Fig. E
6
5603R-y2k (E) (’100. 10. 4)
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Makita 5705r at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Makita 5705r in the language / languages: English, German, Dutch, Danish, French, Italian, Norwegian as an attachment in your email.

The manual is 0,19 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info