Manual Makita 5603r (page 6 of 13) (English, German, Dutch, Danish, French, Italian, Norwegian)

382528

Zoom out

Zoom in

1/13

ENGLISH

Explanation of general view

1 Hex wrench

2 Shaft lock

3 Tighten

4 Loosen

5 Saw blade

6 Outer flange

7 Inner flange

8 Outer flange

9 Hex socket head bolt

0 Saw blade

q Setting protuberances

w Hex socket head bolt

(For adjusting riving knife)

e Cutting depth

r Loosen

t Lever

y Thumb nut

u For 45° bevel cuts

i For straight cuts

o Base plate

p 45° angle cuts

a Straight cuts

s Top guide

d Base

f 60° angle cuts

g 45° angle cuts

h 30° angle cuts

j Straight cuts

k Blade

l Base

; Top guide

z Lock-off button

x Switch trigger

c Vacuum cleaner

v Limit mark

b Brush holder cap

n Screwdriver

SPECIFICATIONS

Model 5603R 5703R 5903R 5103R 5143R

Blade diameter .................................................... 165 mm 190 mm 235 mm 270 mm 355 mm

Max. cutting depth

At 90° ............................................................... 54 mm 66 mm 85 mm 100 mm 130 mm

At 45° ............................................................... 38 mm 46 mm 64 mm 73 mm 90 mm

No load speed (RPM) ......................................... 5,000 4,800 4,500 3,800 2,700

Overall length ...................................................... 330 mm 356 mm 400 mm 442 mm 607 mm

Net weight ........................................................... 4.2 kg 5.2 kg 7.6 kg 9.4 kg 14.5 kg

•

Due to our continuing program of research and

development, the specifications herein are subject

to change without notice.

•

Note: Specifications may differ from country to

country.

Power supply

The machine should be connected only to a power

supply of the same voltage as indicated on the

nameplate, and can only be operated on single-phase

AC supply. They are double-insulated in accordance

with European Standard and can, therefore, also be

used from sockets without earth wire.

Safety hints

For your own safety, please refer to the enclosed

Safety instructions.

ADDITIONAL SAFETY RULES

1. Wear hearing protection.

2. Keep Guards In Place and In Working Order.

Never wedge or tie lower guard open. Check

operation of lower guard before each use.

Don’t use if lower guard does not close briskly

over saw blade.

CAUTION: If saw is dropped, lower guard may

be bent, restricting full return.

3. Do not use blades which are deformed or

cracked.

4. Do not use blades of high speed steel.

5. Do not stop the blades by lateral pressure on

the saw blade.

6. Keep Blades Clean and Sharp.

Sharp blades minimize stalling and kickback.

7. DANGER: Keep Hands Away From Cutting

Area. Keep hands away from blades. Don’t

reach underneath work while blade is rotating.

Don’t attempt to remove cut material when

blade is moving.

CAUTION: Blades coast after turn off.

8. Support Large Panels.

Large panels must be supported as shown in

Fig. A to minimize the risk of blade pinching

and kickback.

When cutting operation requires the resting of

the saw on the work piece, the saw shall be

rested on the larger portion and the smaller

piece cut off.

To avoid kickback, do support board or panel

near the cut.

Fig. A

Don’t support board or panel away from the cut.

Fig. B

5603R – 5413R (E) (’99. 6. 11)

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita 5603r in the language / languages: English, German, Dutch, Danish, French, Italian, Norwegian as an attachment in your email.

The manual is 0,18 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita 5603r Manual

Product: