711074
6
Zoom out
Zoom in
Previous page
1/52
Next page
6
ENGLISH (Original instructions)
Explanation of general view
1 Cutting action changing lever
2 Switch lever
3 Speed adjusting dial
4 Tool opener
5 Blade clamp
6 Jig saw blade
7 Protrusions
8Base
9Hex wrench
10 Cutting line
11 Bolt
12 Graduation
13 Bevel slot
14 Gear housing
15 V-notch
16 Starting hole
17 Dust nozzle
18 Hose for vacuum cleaner
19 Rip fence
20 Fence guide
21 Threaded knob
22 Circular guide pin
23 Rule bar
24 Screw
25 Guide rail adapter
26 Guide rail
27 Cover plate
28 Anti-splintering device
SPECIFICATIONS
Model 4351T 4351CT 4351FCT
Length of stroke............................................................. 26 mm 26 mm 26 mm
Max. cutting capacities
Wood .......................................................................... 135 mm 135 mm 135 mm
Steel ........................................................................... 10 mm 10 mm 10 mm
Aluminum ................................................................... 20 mm 20 mm 20 mm
Strokes per minute (min
–1
) ........................................... 2,800 800 – 2,800 800 – 2,800
Overall length ................................................................ 271 mm 271 mm 271 mm
Net weight ..................................................................... 2.6 kg 2.6 kg 2.6 kg
Safety class................................................................... /II /II /II
Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
Specifications may differ from country to country.
Weight according to EPTA-Procedure 01/2014
ENE019-1
Intended use
The tool is intended for the sawing of wood, plastic and
metal materials. As a result of the extensive accessory
and saw blade program, the tool can be used for many
purposes and is very well suited for curved or circular
cuts.
ENF002-2
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated and can, therefore, also be used from
sockets without earth wire.
GEA010-2
General Power Tool Safety Warnings
WARNING Read all safety warnings, instructions,
illustrations and specifications provided with this
power tool. Failure to follow all instructions listed below
may result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future
reference.
The term “power tool” in the warnings refers to your
mains-operated (corded) power tool or battery-operated
(cordless) power tool.
GEB186-1
JIG SAW SAFETY WARNINGS
1. Hold the power tool by insulated gripping sur-
faces, when performing an operation where the
cutting accessory may contact hidden wiring or
its own cord. Cutting accessory contacting a “live”
wire may make exposed metal parts of the power
tool “live” and could give the operator an electric
shock.
2. Use clamps or another practical way to secure
and support the workpiece to a stable platform.
Holding the workpiece by hand or against your body
leaves it unstable and may lead to loss of control.
3. Always use safety glasses or goggles. Ordinary
eye or sun glasses are NOT safety glasses.
4. Avoid cutting nails. Inspect workpiece for any
nails and remove them before operation.
5. Do not cut oversize workpiece.
6. Check for the proper clearance beyond the work-
piece before cutting so that the blade will not
strike the floor, workbench, etc.
7. Hold the tool firmly.
8. Make sure the blade is not contacting the work-
piece before the switch is turned on.
9. Keep hands away from moving parts.
10. Do not leave the tool running. Operate the tool
only when hand-held.
11. Always switch off and wait for the blade to come
to a complete stop before removing the blade
from the workpiece.
12. Do not touch the blade or the workpiece immedi-
ately after operation; they may be extremely hot
and could burn your skin.
13. Do not operate the tool at no-load unnecessarily.
14. Some material contains chemicals which may be
toxic. Take caution to prevent dust inhalation
and skin contact. Follow material supplier safety
data.
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Makita 4351T at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Makita 4351T in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 1,26 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info