448192
7
Zoom out
Zoom in
Previous page
1/17
Next page
7
ENGLISH
Explanation of general view
1 Wing bolt
2 Water pipe
3Hex wrench 5
4Loosen
5Tighten
6 Wrench 22
7 Inner flange
8 Diamond wheel
9 Outer flange
10 Hex socket head bolt
11 Base
12 Wing nut
13 This end of blade case should
be above the red line.
14 Red line
15 “TEST” button
16 “ON” button
17 Pilot lamp
18 Portable residual current device
(PRCD)
19 Switch trigger
20 Lock-off button
21 Top guide
22 For straight cuts
23 For 45° bevel cuts
24 Clamp
25 Cover (A)
26 Screw
27 Cover (B)
28 Limit mark
29 Brush holder cap
30 Screwdriver
SPECIFICATIONS
Model 4101RH
Wheel diameter .................................................. 125 mm
Max. cutting capacities
At 90° ..............................................................41.5 mm
At 45° ................................................................. 26 mm
No load speed (RPM) ...........................................12,000
Overall length .....................................................236 mm
Net weight .............................................................. 2.9 kg
Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
Note: Specifications may differ from country to country.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. This tool
should be grounded while in use to protect the operator
from electric shock. Use only three-wire extension cords
which have three-prong grounding-type plugs and three-
pole receptacles which accept the tool’s plug.
Safety hints
For your own safety, please refer to the enclosed safety
instructions.
ADDITIONAL SAFETY RULES
1. This tool is equipped with a portable residual
current device. Do not connect the tool to a
power supply without using the PRCD (Portable
Residual Current Device). In case of damage of
the cord, it has to be replaced by the manufac-
turer’s service organization.
2. For additional protection against electric shock,
be sure to WEAR RUBBER GLOVES AND RUB-
BER BOOTS during operation.
3. Check the wheel carefully for cracks or damage
before operation. Replace cracked or damaged
wheel immediately.
4. Use only flanges specified for this tool.
5. Be careful not to damage the spindle, flanges
(especially the installing surface) or bolt. Dam-
age to these parts could result in wheel break-
age.
6. When using the water feed, be careful not to let
water get into the motor. If water runs into the
motor, an electric shock hazard may result.
7. Hold the tool firmly.
8. Keep hands away from rotating parts.
9. Make sure the wheel is not contacting the work-
piece before the switch is turned on.
10. Wait until the wheel attains full speed before cut-
ting.
11. Stop operation immediately if you notice any-
thing abnormal.
12. Do not attempt to lock the trigger in the “ON”
position.
13. Never attempt to cut with the tool held upside
down in a vise. This can lead to serious acci-
dents, because it is extremely dangerous. (Fig.
1)
14. Before setting the tool down after completing a
cut, be sure that the wheel has come to a com-
plete stop.
SAVE THESE INSTRUCTIONS.
OPERATING INSTRUCTIONS
Installing water pipe (Fig. 2)
First, unplug the tool. Loosen the wing bolt on the depth
guide and move the base down. Install the water pipe on
the blade case using the screw as shown in Fig. 2.
Attach the vinyl tube onto the water pipe and attach the
adapter on the vinyl tube to a faucet of water mains pres-
sure. Adjust the amount of water flow by simply adjusting
the water cock.
Installing or removing diamond wheel
Important:
Always be sure that the tool is switched off and
unplugged before installing or removing the wheel.
Hold the outer flange with the wrench and loosen the hex
socket head bolt in clockwise direction with the hex
wrench. Then remove the hex socket head bolt and outer
flange. (Fig. 3)
Install the diamond wheel, outer flange and hex socket
head bolt onto the spindle. Hold the outer flange with the
wrench and tighten the hex socket head bolt in counter-
clockwise direction with the hex wrench. BE SURE TO
TIGHTEN THE HEX SOCKET HEAD BOLT SECURELY.
(Fig. 4)
CAUTION:
Use only the Makita wrench and hex wrench to install or
remove the wheel.
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Makita 4101 RH at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Makita 4101 RH in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 0,39 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info