Manual Makita 3704 (page 10 of 23) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish)

448182

Zoom out

Zoom in

1/23

Circular work (Fig. 13, 14 & 15)

•

Circular work may be accomplished if you assemble

the straight guide and guide plate as shown in

Fig. 13 or 14.

Fig. 13 for cutting circles between 70 mm and

121 mm in radius.

Fig. 14 for cutting circles between 121 mm and

221 mm in radius.

Note:

Circles between 172 mm and 186 mm in radius

cannot be cut using this guide.

•

Min. and max. radius of circles to be cut (distance

between the center of circle and the center of bit)

are as follows:

Min.: 70 mm

Max.: 221 mm

Align the center hole in the straight guide with the

center of the circle to be cut. Drive a nail less than

6 mm in diameter into the center hole to secure the

straight guide. Pivot the tool around the nail in clock-

wise direction.

Trimmer guide (Fig. 16, 17 & 18)

Trimming, curved cuts in veneers for furniture and the

like can be done easily with the trimmer guide. The

guide roller rides the curve and assures a fine cut.

Loosen the wing bolts and secure the tool base

horizontally. Install the trimmer guide on the tool base

with the clamp screw (A). Loosen the clamp screw (B)

and adjust the distance between the bit and the

trimmer guide by turning the adjusting screw (1 mm

per turn). At the desired distance, tighten the clamp

screw (B) to secure the trimmer guide in place.

When cutting, move the tool with the guide roller

riding the side of the workpiece.

Templet guide (Fig. 19, 20, 21 & 22)

The templet guide provides a sleeve through which the bit passes, allowing use of the trimmer with templet

patterns.

Remove the tool base from the tool. Loosen the wing bolts and secure the tool base horizontally. Loosen the

two screws on the tool base.

Place the templet guide on the tool base. There are four convex portions on the templet guide. Secure two of

the four convex portions using the two screws. Install the tool base on the tool.

Secure the templet to the workpiece. Place the tool on the templet and move the tool with the templet guide

sliding along the side of the templet.

NOTE:

The workpiece will be cut a slightly different size from the templet. Allow for the distance (X) between the router

bit and the outside of the templet guide. The distance (X) can be calculated by using the following equation:

Distance (X) =

outside diameter of the templet guide – router bit diameter

MAINTENANCE

CAUTION:

Always be sure that the tool is switched off and

unplugged before carrying out any work on the tool.

Replacement of carbon brushes (Fig. 29 & 30)

Replace carbon brushes when they are worn down to

the limit mark. Both identical carbon brushes should

be replaced at the same time.

To maintain product safety and reliability, repairs,

maintenance or adjustment should be carried out by a

Makita Authorized Service Center.

ACCESSORY

Makita offers an extensive range of trimmer bits which

comply with the latest safety regulations. Specifica-

tions of each type can be found on the following

pages.

3704 (E) (’100. 12. 1)

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita 3704 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 0,38 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita 3704 Manual

Product: