448181
10
Zoom out
Zoom in
Previous page
1/27
Next page
10
Symbols
The following show the symbols used for the tool. Be sure
that you understand their meaning before use.
............. Read instruction manual.
............. DOUBLE INSULATION
............... Wear safety glasses.
........... Do not place hand or fingers close to the
blade.
Intended use
The tool is intended for cutting in wood.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated in accordance with European Standard
and can, therefore, also be used from sockets without
earth wire.
ADDITIONAL SAFETY RULES
FOR TOOL
SAVE THESE INSTRUCTIONS.
1. Wear eye protection.
2. Don't use the tool in presence of flammable liq-
uids or gases.
3. NEVER use the tool with an abrasive cut-off wheel
installed.
4. Check the blade carefully for cracks or damage
before operation. Replace cracked or damaged
blade immediately.
5. Use only saw blades recommended by the manu-
facturer and which conform to EN847-1, and
observe that the riving knife must not be thicker
than the width of the cut by the saw blade and not
thinner than the body of the blade.
6. Always use accessories recommended in this
manual. Use of improper accessories such as
abrasive cut-off wheels may cause an injury.
7. Select the correct saw blade for the material to be
cut.
8. Do not use saw blades manufactured from high
speed steel.
9. To reduce the emitted noise, always be sure that
the blade is sharp and clean.
10. Use correctly sharpened saw blades. Observe the
maximum speed marked on the saw blade.
11. Clean the spindle, flanges (especially the install-
ing surface) and hex nut before installing the
blade. Poor installation may cause vibration/wob-
bling or slippage of the blade.
12. Use saw-blade guard and riving knife for every
operation for which it can be used, including all
through sawing operations. Always install the
blade guard following the instructions out-lined in
this manual. Through sawing operations are those
in which the blade cuts completely through the
workpiece as in ripping or cross cutting. NEVER
use the tool with a faulty blade guard or secure the
blade guard with a rope, string, etc. Any irregular
operation of the blade guard should be corrected
immediately.
13. Immediately reattach the guard and riving knife
after completing an operation which requires
removal of the guard.
14. Do not cut metals such as nails and screws.
Inspect for and remove all nails, screws and other
foreign matter from the workpiece before opera-
tion.
15. Remove wrenches, cut-off pieces, etc. from the
table before the switch is turned on.
16. NEVER wear gloves during operation.
17. Keep hands out of the line of the saw blade.
18. NEVER stand or permit anyone else to stand in
line with the path of the saw blade.
19. Make sure the blade is not contacting the riving
knife or workpiece before the switch is turned on.
20. Before using the tool on an actual workpiece, let it
run for a while. Watch for vibration or wobbling
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Makita 2704 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Makita 2704 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 0,71 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info