598727
27
Zoom out
Zoom in
Previous page
1/28
Next page
27
中文
一般的使用說明
1框
2螺
3 支撐桿
4 內槽 (A)
5 外槽 (B)
6 框架管
7 鎖定板
8 支撐板(僅限於 LS0714
型)
9 支撐桿上的最小的孔
10 調節螺栓
11 斜切鋸底座前孔
12 支撐桿前孔
13 螺栓
14
15 固定板
16 孔 (a)
17 孔 (b)
18 最大的孔
19
20
符號
警告:
進行下列操作前請閱讀並充分理解此手冊
和斜切鋸的使用說明手冊。
將斜切鋸安裝到此支架上前務必要關閉斜
切鋸的電源並拔下電源插頭。
支架應用所附的螺栓將四個腳中的三個固
定在平穩的面上。
此支架僅能用於此手冊中指定型號的斜切
複合斜切鋸滑動斜切鋸和刨板機或電
刨。
將工具固定到支架上前,請打開鎖定。
使用前將工具固定在支撐桿上。
切勿登爬、坐或站在此支架上。
務必要將支架設置成公司銘牌總是朝向操
作者一側。
切勿將此支架與工具一起搬運。
保管或搬運前可折疊上框架並通過緊固支
撐桿背面的螺栓將支撐桿固定。
安裝支架的方法
安裝斜切鋸、復合斜切鋸和滑動斜切鋸時
1. 鬆動支撐桿背面上的螺栓。(圖 1)
2. 開框架,轉動支撐桿,使框架管鑲嵌到
支撐桿的內槽 (A) 內。(圖 1)
3. 根據所使用工具底座上前孔的距離調節兩
個支撐桿的位置按下鎖定板將其鎖定
(圖 1)
注意:
僅當使用 LS0714 機型時要安裝支撐板使
其上面的孔與支撐桿上的最小的孔對齊,
然後用兩個螺栓將其牢牢固定。(圖 2)
4. 轉動支架使其腳上的調節螺栓或公司銘牌
面向您這一側將工具置於支撐桿的中央
本手冊中所指定的所有斜切鋸機型均應放
置成使其底座上面的兩個前孔與兩個支撐
桿上的第一個前孔對齊。(圖 3)
工具底座的兩個後孔將與相應的孔對齊
了。
注意:當工具底座上的孔與支撐桿上的孔未
對齊時,可將鎖定板抬起解除其鎖定,重新
將其進行微細的調節,再將其按下並鎖定。
調節後,要緊緊牢固固好支撐桿背面的螺
栓。(圖 3)
5. 用卜隨支架所附的四個六角螺栓和四個螺
母將工具底座固定到支架的支撐桿上。
務必要將兩個前螺栓和螺母牢固地緊固到
兩個支撐桿上的第一個前孔內。(圖 3)
6. 當支架不能放置穩定時,請轉動支架腳上
的調節螺栓以獲得可靠的穩定性調節後
務必要確保支架和工具均穩定。(圖 4)
7. 用帶有三個六角螺栓的固定板上的孔將支
架腳固定到平穩的面上。(圖 4)
閱讀使用說明手冊。
最大容許負荷。
MAX
100Kg
(220lbs.)
27


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Makita 194043-3 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Makita 194043-3 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 0,9 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info