Manual Makita 1100D (page 8 of 48) (English, German, Dutch, Danish, French, Italian, Portuguese, Spanish)

448165

Zoom out

Zoom in

1/48

For the correct planer blade setting

Your planing surface will end up rough and uneven, unless the blade is set properly and securely. The blade must be

mounted so that the cutting edge is absolutely level, that is, parallel to the surface of the rear base.

Refer to some examples below for proper and improper settings.

Connecting a vacuum cleaner

For tools with European type (round) chip cover

(Fig. 10 & 11)

When you wish to perform clean planing operation, con-

nect a Makita vacuum cleaner to your tool as shown in

Fig. 10 & 11.

For tools with standard (non-round) chip cover

(Fig. 12)

Any Makita vacuum cleaner cannot be connected to the

tool with the standard (non-round) chip cover.

OPERATION

Planing operation (Fig. 13)

First, rest the tool front base flat upon the workpiece sur-

face without the blades making any contact. Switch on

and wait until the blades attain full speed. Then move the

tool gently forward. Apply pressure on the front of tool at

the start of planing, and at the back at the end of planing.

Planing will be easier if you incline the workpiece in sta-

tionary fashion, so that you can plane somewhat downhill.

The speed and depth of cut determine the kind of finish.

The power planer keeps cutting at a speed that will not

result in jamming by chips. For rough cutting, the depth of

cut can be increased, while for a good finish you should

reduce the depth of cut and advance the tool more

slowly.

Shiplapping (Rabbeting) (Fig. 14, 15, 16, 17 & 18)

To make a stepped cut as shown in Fig. 14, use the edge

fence (guide rule).

Draw a cutting line on the workpiece. Insert the edge

fence into the hole in the front of the tool. Align the blade

edge with the cutting line. (Fig. 15)

Adjust the edge fence until it comes in contact with the

side of the workpiece, then secure it by tightening the

screw. (Fig. 16)

When planing, move the tool with the edge fence flush

with the side of the workpiece. Otherwise uneven planing

may result.

Maximum shiplapping (rabbeting) depth is 20 mm.

You may wish to add to the length of the fence by attach-

ing an extra piece of wood. Convenient holes are pro-

vided in the fence for this purpose, and also for attaching

an extension guide (optional accessory). (Fig. 17)

CAUTION:

• The blade edge should be made to protrude outside

slightly (0.3 mm – 0.6 mm). Otherwise, nicks and gen-

erally poor shiplapping results. (Fig. 18)

Chamfering (Fig. 19 & 20)

To make a chamfering cut as shown in Fig. 19 & 20, align

the “V” groove in the front base with the edge of the work-

piece and plane it.

(A)

(B)

(A)

(B)

(A)

(A) Front base (Movable shoe)

(B) Rear base (Stationary shoe)

Correct setting

Nicks in surface

Gouging at start

Gouging at end

Although this side view cannot show it,

the edges of the blades run perfectly

parallel to the rear base surface.

Cause: One or both blades fails to

have edge parallel to rear

base line.

Cause: One or both blade edges fails

to protrude enough in relation

to rear base line.

Cause: One or both blade edges

protrudes too far in relation to

rear base line.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita 1100D in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 1,07 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Makita 1100D

Makita 1100D User Manual - English, Dutch - 17 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita 1100D Manual

Product: