494170
15
Zoom out
Zoom in
Previous page
1/37
Next page
English
15
EN
INTRODUCTION PREPARATION WATCHING TV
OPTIONAL SETTING
TROUBLESHOOTING
INFORMATION
These operations are accessible by remote control.
Some may also be accessible by controls on the main unit.
Initial Setup
This section will guide you through the unit’s initial setting
which includes selecting a language for your on-screen menu
and autoprogram, which automatically scans and memorizes
viewable channels.
Before you begin:
Make sure the unit is connected to antenna or cable.
1 After making all the necessary connections,
press
to turn on the unit.
It may take a few moments to turn on the unit for the
first time.
[Initial Setup] menu appears automatically after the
unit is turned on.
2 Use / to select the on-screen language from the
choices (English / Español / Français) on the right side of the
TV screen.
3 Use / to select [Antenna] for TV channels or [Cable]
for CATV channels, then press OK.
Initial Setup
Make sure the antenna is connected to ''ANT. IN'' jack.
Select your signal source.
Antenna
Cable
ANT.IN
Antenna
Cable
Or
Skip
Select
OK
OK
BACK
Back
MENU
Skip
[Autoprogram] will begin.
Initial Setup
Please wait while the system is scanning for channels. Auto programming
may take more than 20 minutes to complete.
0%
Digital channels
0 ch
Analog channels
0 ch
MENU
Skip
4 Use / to select the desired location setting, then
press OK.
Initial Setup
Select “Retail” or “Home” for your location.
Retail
Home
Select
OK
OK
• Select [Retail] store, the unit will be set up with
predefined setting for retail displays. In this setting, the
power consumption may possibly exceed the limited
requirement of the ENERGY STAR
®
qualification.
• Select [Home], the unit is set to maximize the energy
efficiency for home setting and it can be adjusted
through a choice of picture and sound quality according
to your preference.
When the initial setup is completed, the lowest
memorized channel with the confirmation message of
the location setting will be displayed on the TV screen.
Note
If you are not receiving a signal from your cable service, contact the Cable
provider.
If you press or MENU during autoprogram, this setting will be canceled.
The initial autoprogram function can be executed for either [Antenna] or
[Cable] only once. When you change the connection (Antenna / Cable),
set [Autoprogram] again.
p. 19
If there is no signal input from the antenna terminal and no operation for
several seconds after you turn on the unit, [Helpful Hints] appears. Follow
the instructions listed on the TV screen.
Initial Setup
No channel is registered.
Try Autoprogram again?
Verify that you have a cable connected to the "ANT. IN" jack on the back
of the TV, the channel installation process searches this connection. If
you are using a cable or satellite box, please confirm the input which
you have connected the box and press "SOURCE" key on the remote
control to select the appropriate source input.
Retry
Later
Select
OK
OK
MENU
Skip
You must set [Home] in step 4. Otherwise, [Picture] and [Sound] settings
you adjusted will not be memorized after the unit goes to the standby mode.
After an initial setup is completed...
If you want to scan the channels automatically again.
[Autoprogram] p. 19
You can add the desired cable and analog channels
unmemorized by autoprogram.
[Add Channels] p. 20
If you want to change to another language.
[Language Selection] p. 21
If you want to change the location setting.
[Location] p. 30
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Magnavox 46MF401B at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Magnavox 46MF401B in the language / languages: English as an attachment in your email.

The manual is 4,06 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info