Manual Magnat tribal x two (page 10 of 68) (English, German, Dutch, French, Italian, Portuguese, Swedish, Spanish)

167356

Zoom out

Zoom in

1/68

· Mute switch for suppressing switch-on crackle interference

· Low-level outputs (cinch jacks) for connecting additional amplifiers

· Operating display (green LED) and overload indicator (red LED)

3. IMPORTANT INSTALLATION INFORMATION

· This appliance may only be connected to a 12 volt system with negative ground.

· The heat radiated when the amplifier is used means that sufficient air circulation is required

at the place of installation. It is very important that the cooler’s cooler ribs do not contact

any metal plating or any surfaces which could impair air circulation. The amplifier may not

be installed in small confined spaces or spaces without air circulation (e.g. spare wheel

recess or under the vehicle carpeting). Installation in the boot is recommended.

· Install the amplifier in such a way that it is protected as far as possible against vibrations

and dust and dirt.

· Make sure that the input/output cables are sufficiently distant from the power supply cables

as otherwise interference may occur.

· Make sure that the fuse and operating elements are accessible after installation.

· The appliance’s reliability and performance depend on the quality of installation. Preferably

get an expert to install the system, particularly if you want to install several loudspeakers

or a complex multi-way system.

4. CONNECTIONS

4.1 POWER SUPPLY AND AUTOMATIC SWITCHING ON

Important notice: Before commencing the installation, disconnect the plus terminals

from the car battery in order to prevent short circuits.

The power cabling usually installed in on-board car networks is not sufficient for a power

amplifier’s demands. Make sure that the power lines to GND and to the +12 V terminal have

been sufficiently specified. A cable cross-section of at least 10 mm² must be used to connect

the battery to the amplifier’s terminals.

First connect the amplifier’s GND terminal to the battery’s minus pole. It is very important that

the connection is good. Dirt residues must be carefully removed from the battery’s connection

point. A loose connection may cause malfunctions or interference noise or distortion.

The +12 V amplifier connection must then be connected with a power cable possessing an

integrated fuse to the battery’s plus pole. The fuse must be located close to the battery, the

length of cable from the battery’s positive pole to the fuse must be less than 60 centimetres

for safety reasons. Only insert the fuse when all installation work, including the connection of

the loudspeakers, has been completed.

Now connect the car hi-fi receiver’s remote control connection to the amplifier’s REM control

jack. A cable with a cross-section of 0.75 mm² is sufficient for connecting the amplifier’s

REMOTE connection and the control device.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Magnat tribal x two in the language / languages: English, German, Dutch, French, Italian, Portuguese, Swedish, Spanish as an attachment in your email.

The manual is 1,37 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Magnat tribal x two Manual

Product: