581709

Magnat INTERIOR ICP 82 Manual

7
Zoom out
Zoom in
Previous page
1/44
Next page
Dear MAGNAT Customer,
Congratulations on your ne new loudspeakers and thank you very much for choosing MAGNAT! You
have made an excellent choice. The high-quality speakers produced by MAGNAT are renowned all over
the world.
Please study the instructions and information below carefully before using your new loudspeakers.
MAGNAT INTERIOR ICP/IWP LOUDSPEAKERS - SPECIALLY DESIGNED FOR CEILING FITTING/
WALL MOUNTING (FIG. 1)
MAGNAT INTERIOR ICP/IWP speakers have an ingenious clamping mechanism that enables you to
easily t them into a hole cut into a bafe. The easiest way is to t them in a plaster board or similar
ceiling. When using an opening in a masonry wall, a plaster or timber board is also needed. For the tting
dimensions, please see the technical data given at the end of the manual.
The clamping mechanism for attaching the speaker can be accessed after removing the protective grille.
Loosen the screws and move the clamps to position A. After placing the appliance in the cut-out hole,
tighten the screws. This automatically turns the clamps to position B and tightens them.
GENERAL INFORMATION ABOUT CONNECTING YOUR MAGNAT LOUDSPEAKERS
Please always use a good quality loudspeaker connection cable from an audio dealer. To prevent
impairment of sound quality, we recommend cables with cross-sections of at least 1 mm² for lengths up
to 3 m and at least 1.5 mm² for lengths above 3 m.
Always turn off the amplier or receiver before connecting or disconnecting loudspeaker cables. Place
the loudspeakers in their planned positions and cut the cables to the right length. The cables for both
channels should always be exactly the same length.
Strip 10 – 15 mm of insulation from the ends of the cables and twist the ends. The loudspeaker terminals
are equipped with a clamping mechanism (g. 2). Press the terminal head down and guide the stripped
cable end into the hole on the side. On releasing the terminal head, the cable is secured, ensuring the
best possible contact.
For good sound it is imperative that the cables must be connected in such a way that the speakers are
“in phase”. This means that the black negative terminals on the speakers (-) must be connected to the
negative (-) terminals on the amplier, the red positive (+) speaker terminals to the positive (+) amplier
terminals. To make this easier one wire of most speaker cables is marked with a coloured strip or a ridge
in the insulation.
Before switching on the system double-check all your connections and make sure that the terminal screws
are tight and that there are no short circuits caused by stray wire laments – this could cause serious
damage to your amplier!
TWEETER LEVEL ADJUSTMENT (FIG. 3)
The crossover facilitates individual sound adjustment of the speaker system via high-quality jumpers.
It is advisable to conduct the optimum setting according to your own personal listening preferences. We
recommend the following switch positions as a basic setting for various listening areas:
GB
7
… 7 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Magnat INTERIOR ICP 82 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Magnat INTERIOR ICP 82 in the language / languages: English, German, Dutch, French, Italian, Portuguese, Swedish, Spanish as an attachment in your email.

The manual is 1,2 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info