Manual Magnat Edition Two (page 10 of 64) (English, German, Dutch, French, Italian, Portuguese, Swedish, Spanish)

581722

Zoom out

Zoom in

1/64

Sizes (W x H x D) 221 x 57 x 236 mm

Weight 2.15 kg

SUBJECT TO TECHNICAL CHANGE

2. FEATURES

· Complementary push-pull final stage

· Automatic switching on/off via car radio

· Infinitely adjustable high pass and low pass filters

· Infinitely variable bass equalisation

· Adjustable input sensitivity

· Bridgeable 2-/1-channel mode

· Tri-mode

· Electronic protective circuit against short circuiting, DC offset and excess temperature

· Mute switch for suppressing switch-on crackle interference

· Low-level outputs (cinch jacks) for connecting additional amplifiers

· Operating display (green LED) and overload indicator (red LED)

3. IMPORTANT INSTALLATION INFORMATION

· This appliance may only be connected to a 12 volt system with negative ground.

· The heat radiated when the amplifier is used means that sufficient air circulation is required at the

place of installation. It is very important that the cooler’s cooler ribs do not contact any metal plating

or any surfaces which could impair air circulation. The amplifier may not be installed in small confined

spaces or spaces without air circulation (e.g. spare wheel recess or under the vehicle carpeting).

Installation in the boot is recommended.

· Install the amplifier in such a way that it is protected as far as possible against vibrations and dust

and dirt.

· Make sure that the input/output cables are sufficiently distant from the power supply cables as

otherwise interference may occur.

· Make sure that the fuse and operating elements are accessible after installation.

· The appliance’s reliability and performance depend on the quality of installation. Preferably get an

expert to install the system, particularly if you want to install several loudspeakers or a complex multi-

way system.

4. CONNECTIONS

4.1 POWER SUPPLY AND AUTOMATIC SWITCHING ON

Important notice: Before commencing the installation, disconnect the plus terminals from the car

battery in order to prevent short circuits.

The power cabling usually installed in on-board car networks is not sufficient for a power amplifier’s

demands. Make sure that the power lines to GND and to the +12 V terminal have been sufficiently

specified. A cable cross-section of at least 10 mm² must be used to connect the battery to the amplifier’s

terminals.

First connect the amplifier’s GND terminal to the battery’s minus pole. It is very important that the

connection is good. Dirt residues must be carefully removed from the battery’s connection point. A loose

connection may cause malfunctions or interference noise or distortion.

The +12 V amplifier connection must then be connected with a power cable possessing an integrated

fuse to the battery’s plus pole. The fuse must be located close to the battery, the length of cable from the

battery’s positive pole to the fuse must be less than 60 centimetres for safety reasons. Only insert the

fuse when all installation work, including the connection of the loudspeakers, has been completed.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Magnat Edition Two in the language / languages: English, German, Dutch, French, Italian, Portuguese, Swedish, Spanish as an attachment in your email.

The manual is 0,93 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Magnat Edition Two Manual

Product: