581721
9
Zoom out
Zoom in
Previous page
1/52
Next page
9
GB
5. OPERATING ELEMENTS AND IN/OUTPUTS
5.1 SETTING THE INPUT SENSITIVITY
The input sensitivity may be adapted to any car radio or tape deck. Turn the volume control of your radio to its
central position and then adjust the input-level control (2) to produce an average medium volume. This setting
usually provides sufficient power reserves at optimum weighted noise voltage.
ATTENTION: only reproduce loud test noises briefly to prevent damaging the loudspeakers.
5.2 LOW-PASS FILTER WITH ADJUSTABLE CROSS-OVER FREQUENCY
Set the desired cross-over frequency with the control (4). This makes the filter adaptable to the installed woofers
sound requirements. The filter’s high edge steepness is responsible for the precision reduction of medium and
high frequency ranges.
5.3 SUBSONIC FILTER
The subsonic function reduces the lowest bass frequencies. The reduction rate may be infinitely adjusted with
the regulator (3). This allows distortions produced by excessive loudspeaker membrane movements to be
effectively minimized without reducing the utilizable bass levels.
5.4 BASS-BOOST
The bass-boost function (5) is used to increase or equalize the lower bass frequencies.
5.5 VOLUME REMOTE CONTROL
The volume may be adjusted by using the supplied remote control. Please observe during installation that the
remote control line shouldn’t be routed along the same side of the vehicle as the power supply cables. The
remote control unit should be mounted on the dashboard or at any other easily accessible position. Now, the
subwoofer volume may be adjusted independently from the settings at the radio.
5.6 OUTPUTS FOR CONNECTING ADDITIONAL AMPLIFIERS
The input signal of the INPUT connections INPUT L and R (1) is forwarded directly to the OUTPUT (6) L and
R jacks. The OUTPUT connections allow the use of additional amplifiers without requiring additional T-plugs
and cables.
FIG. 1 POWER SUPPLY / REMOTE SWITCH-ON CONNECTION
(1) GND terminal for the ground, to the battery’s minus pole
(2) REM terminal for remote switch-on
(3) Terminal for +12 V battery voltage
(4) Battery
(5) Cable fuse
(6) To your car radio’s automatic aerial connection
If your car is not equipped with an automatic aerial connection, connect this cable’s plus pole (+) to the
ignition lock. An on/off switch should be inserted in this case. Make sure that this switch is switched off if
the amplifier is not used.
9


Need help? Post your question in this forum.

Forumrules
1

Forum

magnat-edition-mono

Reset search

  • Hallo gesucht wird das Schaltbild zum Magnat Monoverstärker 800watt Submitted on 20-1-2023 at 16:37

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Magnat Edition Mono at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Magnat Edition Mono in the language / languages: English, German, Dutch, French, Italian, Portuguese, Swedish, Spanish as an attachment in your email.

The manual is 1,1 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info