Start up (4-8)
Before using the machine for the first time,
we advise you to clean it as follows:
●
connect the power plug
●
fill the water tank with fresh, cold water
(1-3)
●
place the empty capsule holder in the capsule
holder ring and turn from left to right.
When it is correctly inserted, the handle
faces forwards or slightly to the right (4)
●
place a sufficiently large receptacle under
the capsule holder and another under the
steam/hot water nozzle (5)
●
press key to start the machine (6).
The words FILL WATER appear on the display
●
turn the switch to position ; water now
emerges from the steam/hot water nozzle
and the word WATER appears on the
display (7)
●
allow around 1/2 a litre of water to flow.
Then reset the switch to position «O».
READY appears on the display
●
to clean the coffee system, now press the
key . LARGE appears on the display (8).
This allows the quantity of water preset in the
factory to flow through the coffee system.
Repeat this operation five times.
Programming the
machine (9)
Access to the programming mode
To access the programming mode, the machine
must be connected to the power supply.
Press the key /P (approx. 3 sec.) until TIME
appears on the display.
When the programming mode is activated,
the following messages appear on the display:
TIME AUTO ON AUTO OFF HARDNESS
CUPS DECAL. LANGUAGE
To quit the programming mode, press the key
/P until the message READY appears on the
display, or if the machine has not yet warmed
up, WAIT.
Selection of the different programming
points
Press the key /P to select the different
programming points. As soon as the desired
programming point appears on the display,
press the key /«+» or the key /«-» to
access the corresponding programming point.
You can modify the setting of the programming
points by pressing the key /«+» or the
key /«-».
Setting the TIME
When the word TIME appears on the display,
the display changes to --.--. Now press the
key /«+» or /«-» and the time display
flashes. You can now adjust the time with the
key /«+» or /«-».Confirm the entry by
pressing the key /P. The minutes display now
flashes. Set the exact time by pressing the
key /«+» or /«-». Confirm the entry by
pressing the key /P again.
Note: --.- - Function deactivated
00:00 Midnight
This function is not activated in the factory.
If the machine is disconnected from the power
supply, the time will have to be reprogrammed.
AUTO ON setting
When this programming point is activated, your
machine starts automatically. This message only
functions correctly if you have first set the right
time. Press the key /P until the message
AUTO ON appears on the display.
Now press the key /«+» or /«-».
The time display flashes. You can now set the
time using the keys /«+» or /«-». Confirm
the entry by pressing the key /P. The minutes
display now flashes. Set the exact time by
pressing the key /«+» or /«-». Confirm
the entry again by pressing the key /P.
Note: --.- - Function deactivated
00:00 Midnight
This function is not activated in the factory.
If the machine is disconnected from the power
supply, the time will have to be reprogrammed.
AUTO OFF setting
When this function is on, your machine stops
automatically. However, if the machine is
reactivated before it automatically stops, the
machine will automatically re-start from the original
programming time. e.g. if the machine is
programmed on at 11 a.m. and is due to switch
off at 12 noon, if it is reset at 11.55 a.m. the
machine will then switch off at 12.55 p.m.
This programming point functions, regardless
of whether you have set the time.
Press the key /P until AUTO OFF is displayed
on the display.
Wait until – HRS begins to flash. Press the
key /«+» or /«-» to enable the setting to
be adjusted. Now you can set the desired stop
time with the key /«+» or the key /«-».
Confirm the entry, by pressing the key /P.
Note: -- HRS Function deactivated
15h Maximum deactivation time
This function is not activated in the factory.
If the machine is disconnected from the power
supply, the time will have to be reprogrammed.
Setting the water hardness
Limescale is the main cause of malfunctioning.
Therefore your machine has an automatic
scaling control. To enable this display to function
properly, you must set the correct water
hardness. Use the enclosed test tab to
determine the hardness. For this purpose,
dip the tab briefly (1 second) in a glass
containing tap water. Shake off excess and
leave to dry for around 1 minute. Now you
can read the degree of hardness.
Value of the levels :
4 green boxes = Very soft ......
❑ Set level 1
1 red box = Soft ....................
❑ Set level 1
2 red boxes = Medium ..........
❑ Set level 2
3 red boxes = Hard................
❑ Set level 3
4 red boxes = Very hard ........
❑ Set level 4
The factory setting is programmed to level 3.
Once you have programmed the water hardness
the level will stay memorised – even if the
machine is disconnected from the mains.
Displaying the number of cups
Press the key /P until the word CUPS appears
on the display. Release the key and the number
of cups now appears on the flashing display.
Descaled display
Press the key /P until DECALC appears on
the display. Release the key and the number of
descaling operations effected flashes on the display.
ENGLISH
ENGLISH
