166345
9
Zoom out
Zoom in
Previous page
1/30
Next page
9
CONTROLS AND INDICATORS
9 • Speaker connectors: Outputs for connecting the loudspeakers.
The amplifier allows the loudspeakers to be connected with a minimum impedance of 2 Ohm
for a channel in stereo configuration, and with an impedance of 4 Ohm for a "bridged" mono
connection.
If the 3 channel configuration is to be used, the total impedance should not exceed the
minimum value of 2 Ohm.
Make sure that the polarity of the connection between the loudspeakers is correct. Do not
allow inadequately insulated leads to come into contact with Ground,
any metallic parts of the car, or with each other.
10 • Fuses: When replacing fuses, make sure that they are replaced with fuses of the same
ampere rating. Use of the wrong type of fuse could seriously damage the components.
11 + BATT connector: Connect the positive "+" of the battery directly, by means of a fuse
located nearby, and use a lead having a sufficiently large cross-section to allow passage of the
current. Do not connect this terminal to the car's own electrical circuit.
12 • REMOTE-ON connector: Connect this to the remote-on start-up output lead (remote
starting switch) or to the automatic antenna wire running from the main unit. It will now be
possible to turn the amplifier on and off from the main unit.
13 • GND connector: Attach this Ground connector, using a lead of adequate section, to a
clean point on any metallic part of the car chassis, if possible to an already-installed screw.
Never attach this clamp directly to the negative point of the battery, which could give rise to an
unpleasant buzzing noise while the car is being driven.
14 • Check control indicator: This LED indicates the amplifier functioning status.
WHITE: The unit is switched off
GREEN: The amplifier is functioning perfectly
RED: the unit is in a state of protection.
The amplifier is equipped with three protection devices:
- Overheating: If errors have been made during installation, and the amplifier overheats, the
unit will enter into a state of protection before any damage can occur. Once the temperature
returns to normal and the errors have been rectified, the unit will automatically start to function
normally once again.
- Overloading: If several loudspeakers have been connected to the amplifier and the total
impedance drops below the 1 Ohm limit that it can handle, the amplifier goes into a state of
protection. The main unit will have to be switched off and on again in order to restore the
amplifier to normal functioning.
- Short circuit in an output: In the case of a short circuit in the loudspeaker outputs, the unit will
go into a state of protection to avoid serious damage to the final transistors. Normal
functioning will be restored when the short circuit has been dealt with and the main unit
switched on again.
RL
Bridged
RL
Bridged
RL
Bridged
3-channel configuration 2-channel configuration 1-channel configuration
O/M ST 2.100 25/06/02 18:28 Page 9
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Macrom st 2100 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Macrom st 2100 in the language / languages: English, German, French, Italian, Spanish as an attachment in your email.

The manual is 0,34 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info