494083
27
Zoom out
Zoom in
Previous page
1/30
Next page
In case of difficulty
24
Others
If operation freezes, the screen goes black or the unit should otherwise not function properly,
try turning the power off then back on. Alternatively, try the following methods in the order
listed until the unit returns to normal playback mode.
1) Turn the car’s ignition OFF and back ON again.
2) Press the RESET button on the face of the unit
This guide will help you isolate the problem if the unit is at fault. Otherwise, make sure the
rest of your system is properly connected or consult a professional mobile video installer.
Unit does not
operate.
Fuse is blown.
Monitor’s power is not turn on.
Condensation
Replace with a fuse of the specified capacity.
Turn on the m onitor’s power
Wait a while(about 1 hour) for the condensation
to dry.
Operation is
unstable.
Remote control unit’s
battery is worn.
Replace the remote control unit’s battery with
new one.
Remote control sensor or
transmitter is dirty.
Clean the sensor or transmitter.
No picture is
produced.
Monitors mode is not
switched to the mode you
want to see.
Switch to the mode you want to see.
Playback does
not start.
Disc is loaded upside-down.
Check the disc and load it with the labeled side
facing upward.
Disc is dirty.
Clean the disc.
A disc not able to playback
with this unit is loaded.
Check if the disc is able to be played back.
Parental lock is set.
Cancel the parental lock or change the rating
level.
Picture is
unclear or noisy
Disc is being fast-forwarded
or fast-reversed.
The picture may be slightly disturbed, but this
is normal.
Vehicle’s battery power is
weak.
Check the battery power and wiring.
The unit may malfunction if the battery power is
under 10.8 volts with a load applied.
Monitors fluorescent tube is
worn.
Replace the monitor’s fluorescent tube.
Image stops
sometimes.
Disc is scratched.
Replaced with a non-scratched disc.
No disc
No disc is loaded.
Load a disc.
Disc is dirty.
Clean the disc.
Not valid
Remote control operation
is not possible.
For some discs or playing modes, certain
operations are not possible. This not a
malfunction.
VIDEO SIGNAL
SYSTEM IS NOT
CORRECT
PAL( or NTSC) disc is loaded.
Change the TV TYPE of the unit(see SET UP).
Symptom Cause Remedy
No sound Select the wrong Audio Out
According to the connection, set ANALOG for
using audio cable, set SPDIF/RAM/PCM for
using coaxial cable. See page 7,8 and 19.
27


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Macrom M-DVD9900 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Macrom M-DVD9900 in the language / languages: English as an attachment in your email.

The manual is 3,64 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info