166337
8
Zoom out
Zoom in
Previous page
1/26
Next page
8
CONTROLS AND INDICATORS
8 • PRE-OUTPUT RCA OUTPUT CONNECTORS: connect to an additional amplifier to be
used according to the mode previously selected.
9 • SPEAKER CONNECTOR: outputs for speakers connection. The amplifier allows to
connect speakers with minimum 1-ohm impedance per channel in stereo configuration and
with minimum 2-ohm impedance in mono-bridged configuration. Should the 3-channel
configuration be used, total impedance must not exceed the minimum 2-ohm value.
Be sure to keep the right polarity and phase in connecting the speakers. Avoid any contact
between poorly insulated wires and the cars ground or metal pieces and between the wires
themselves.
10 • FUSE: in case of fuse replacement make sure to use fuses of the same amperage. The
use of fuses with the wrong amperage may seriously damage the components of the unit.
11 • BAT + CONNECTOR: to be connected directly to battery + by means of a fuse located
close to the battery itself. Utilize a cable having an adequate section. Do not connect this
cable to the cars electrical system wiring (eg.: dome-light circuit, car radio etc.)
12 • GND CONNECTOR: connect the ground terminal to a clean base metal part of the
vehicle chassis (if possibile, to an existing screw). Utilize a cable having an adequate section.
13 • REMOTE-ON CONNECTOR: to be connected either to the remote switch-on output lead
or to the output lead of the power antenna coming from the head unit. As a resul, the 42.29 will
be switched on and off simultaneously with the head unit.
14 • CHECK CONTROL LED: this led shows the amplifier’s status of operation:
WHITE: the unit is off
GREEN: the unit is working OK
RED: the unit has entered the protection mode
The 42.29 is equipped with three different protection devices:
Overheating: in case of wrong installation the unit enters the protection mode before being
damaged. As soon as the temperature returns to normal values, the unit resumes normal
operation.
Overload: if several speakers are connected to the amplifier and the total impedance
decreases below the allowable threshold (0.5 - 1 ohm), the amplifier enters automatically the
protection mode to avoid any damage. To restore normal operation the head unit has to be
switched off and then on again.
Output short circuit: in case of a short circuit at the speakers outputs, the unit enters the
protection mode to avoid serious damage to the end stage transistors. Normal operation is
restored by eliminating the short circuit and by switching on the head unit again.
++
+
BRIDGED
L R
++
+
BRIDGED
L R
++
+
BRIDGED
L R
3-channel configuration 2-channel configuration 1-channel configuration
O/M 42.29 26/06/02 10:19 Page 8
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Macrom 42 29 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Macrom 42 29 in the language / languages: English, German, French, Italian, Spanish as an attachment in your email.

The manual is 0,23 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info