782329
25
Zoom out
Zoom in
Previous page
1/28
Next page
25
Problem Possible cause Solution
1. Engine does not start 1.1 Not enough fuel in fuel tank
1.2 Spark plug is wet
1.3 Spark plug is damaged
1.4 Spark plug connector lose
1.5 Throttle lever not in the correct
position for the prevailing conditions
1.6 Air lter is dirty
1.7 Spark plug loose
1.8 Spark plug gap is incorrect
1.9 Carburettor is ooded with fuel
1.10 Faulty ignition module
1.1 Add fuel
1.2 Dry spark plug
1.3 Replace spark plug
1.4 Attach properly
1.5 Move throttle lever to correct position
1.6 Clean air lter
1.7 Tighten spark plug 20 N m
1.8 Set gap between electrodes at
0.51 mm
1.9 Remove air lter and pull recoil
starter handle continuously until
carburettor clears itself and install
air lter
1.10 Contact the service agent
2. Engine stops 2.1 Not enough fuel in fuel tank
2.2 Cutting device is blocked
2.1 Add fuel
2.2 Remove blockage
3. Engine to start or loses power 3.1 Dirt, water or stale fuel in the tank
3.2 Vent hole in fuel tank cap is clogged
3.3 Air lter is dirty
3.1 Drain fuel and clean tank. Fill tank
with clean, fresh fuel
3.2 Clean or replace fuel tank cap
3.3 Clean air lter
4. Engine operates erratically 4.1 Spark plug is defective
4.2 Spark plug gap is incorrect
4.3 Air lter is dirty
4.1 Install new, correctly gapped plug
4.2 Set gap between electrodes at
0.51 mm
4.3 Clean air lter
5. Engine idles poorly 5.1 Air lter is dirty
5.2 Air vents are clogged
5.3 Cylinder ns are blocked
5.1 Clean air lter
5.2 Remove debris from vents
5.3 Remove debris from cylinder
6. Engine skips at high speed 6.1 Gap between electrodes of spark
plug is too close
6.1 Set gap between electrodes at
0.51 mm
7. Engine overheats 7.1 Air vents are clogged
7.2 Incorrect spark plug
7.1 Remove debris from vents
7.2 Install correct spark plug and cylinder
ns on engine
8. Unsatisfactory result 8.1 Cutting device dull
8.2 Cutting material exceeds capacity
8.3 Cutting height is incorrect
8.1 Replace with a new one
8.2 Only cut materials acc. to the
capacity of the product.
8.3 Adjust cutting height
9. Excessive vibration/ noise or exhaust 9.1 Cutting device is dull/damaged
9.2 Bolts/nuts are loose
9.3 Petrol/oil is incorrect
9.1 Replace with a new one
9.2 Tighten bolts/nuts
9.3 Empty out unused petrol/oil and rell
with the correct petrol/oil
25


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Mac Allister MLMP300HP46 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Mac Allister MLMP300HP46 in the language / languages: English as an attachment in your email.

The manual is 7.98 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info