782329
22
Zoom out
Zoom in
Previous page
1/28
Next page
22
Product maintenance
Before and after each use, check the product and accessories (such as application tools) for wear and damage. If required,
exchange them for new ones as described in this instruction manual. Observe the technical requirements.
01
Underbody and cutting device
1. Keep the underbody and cutting device (22) clean and free of debris. Remove clippings from the discharge chute.
2. Check all nuts and bolts periodically for tightness before operation. After prolonged use, especially in sandy soil conditions, the
cutting device will become worn and lose some of the original shape. The cutting efciency will be reduced and the cutting device
should be replaced.
3. Keep the cutting device (22) sharp to ensure a good cutting performance. Replace a worn or damaged cutting device with a new
one of the same type or have it sharpened by a qualied specialist.
4. Loosen the blade tension bolt (22e) anti-clockwise using a wrench and remove it together with a cone washer (22d), cutting
device (22), blade adaptor (22c) and key (22b).
5. Replace the cutting device with a new one of the same type. Slide the key (22b) into the slot on the spindle (22a). Ret the blade
adaptor (22c), locking the cone washer (22d) and blade tension bolt (22e). Tighten the blade tension bolt clockwise with 35 N m
min, 40 N m max. to ensure safe operation of the product.
6. Lubricate the cutting device (22) after each use to prolong the life span of cutting device and product. Apply light machine oil
along the edge of the cutting device.
WARNING! Wear protective gloves when working on the
cutting device and close to it! Use proper tools to remove
debris, e.g. a wooden stick! Never use your bare hands.
Always use original spare parts for replacement. The
cutting device must be replaced by an identication no. ref.
SMV 460206G
DO NOT attach any other type of cutting device!
The replacement of the cutting device should be done by
an experienced user. Rework or sharpening blades is not
recommended unless it is done by a repair service or a
similarly qualied specialist.
NOTE: We strongly recommend jacking the product up when
performing inspection and work on the cutting device. Avoid
tilting the product in order to prevent fuel and oil leakages.
22


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Mac Allister MLMP300HP46 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Mac Allister MLMP300HP46 in the language / languages: English as an attachment in your email.

The manual is 7.98 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info