680028

M-System MIO 640 Manual

12
Zoom out
Zoom in
Previous page
1/56
Next page
*5 (# '3
CONVERSIONE AD ALTRO
TIPO DI GAS
Prima della conversione ad
altro tipo di gas, accertatevi del
tipo per il quale l’apparecchio è
stato regolato. (etichetta
adesiva (Figura 1) applicata
sull’apparecchio).
Per il diametro dell’ugello
riferirsi alla tabella degli ugelli.
Sostituzione dell’ugello del
bruciatore inferiore
Rendere privo di tensione
l’apparecchio;
1) Estrarre la suola
copribruciatore (vedi
ESTRAZIONE DELLA
SUOLA pagina 42).
2) Svitare la vite di fissaggio
del bruciatore del forno ed
estrarre dal supporto
insieme all’elemento termico
e alla candela di
accensione. (Figura 5)
3) Togliere l’ugello dall’attacco
con una chiave a tubo da 7
(Figura 6)
4) Avvitare a fondo il nuovo
ugello (diametro impresso in
centesimi di millimetro
sull’ugello) facendo
attenzione all’inserimento
preciso del filetto.
5) Montare il bruciatore
procedendo in ordine
inverso rispetto a quanto
descritto al punto 2.
6) Reinserire la suola nella
7) Regolazione del minimo (vedi
istruzioni a pagina 16)
posizione giusta.
Fig. 5 - Abb. 5 - Afb. 5 Fig. 6 - Abb. 6 - Afb. 6
CONVERSION TO A
DIFFERENT TYPE OF GAS
Before converting the
appliance for operation with a
different gas type, check which
type of gas it is currently set to
operate with (adhesive label
(Figure 1) on appliance).
For the correct nozzle
diameter, refer to the relative
table in this booklet.
Disconnect the electrical
power supply to the appliance;
1) Remove the burner cover
Replacing the lower burner
nozzle
plate (
see REMOVAL OF
THE BURNER COVER
PLATE page 42).
2) Remove the screw securing
the oven burner and
withdraw the burner from
the support together with
the heat sensor and the
ignition spark plug. (Figure
5)
3) Remove the nozzle using a
7 mm box wrench (Figure 6)
4) Screw the new nozzle in
fully (diameter in hundredths
of millimetre stamped on the
nozzle), taking care not to
cross the thread.
5) Replace the burner
reversing the operations in
step 2 above.
6) Replace the cover plate.
7) Adjusting the minimum flame
(see instructions on page 16)
CONVERSION D
E TYPE DE
GAZ
Avant la conversion du gaz,
vérifier que le gaz actuel est
correctement réglé (étiquette
adhésive (Figure 1) appliquée
sur l’appareil).
Pour le diamètre du gicleur,
consulter la table des gicleurs.
Couper la tension;
1) Extraire la sole cache-
Remplacement du gicleur
du brûleur inférieur
brûleur (
voir EXTRACTION
sole page 42).
2) Dévisser la vis de fixation du
brûleur et extraire du
support avec l’élément
thermique et la bougie
d’allumage (Figure 5).
3) Retirer le gicleur de la
fixation avec une clé à
douille de 7 (Figure 6)
4) Visser à fond le nouveau
gicleur (diamètre en
centièmes de millimètres
sur le gicleur) en faisant
attention à l’insertion précise
du filetage.
5) Monter le brûleur en
procédant dans l’ordre
inverse du point 2.
6) Remettre en place la sole.
7) Réglage du minimum (voir
directives page 16)
12
… 12 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for M-System MIO 640 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of M-System MIO 640 in the language / languages: English, German, Dutch, French, Italian, Portuguese as an attachment in your email.

The manual is 1,68 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info