584623
4
Zoom out
Zoom in
Previous page
1/28
Next page
4
Network and Power Amplifiers: The active crossover network and power amplifiers for the
BX8 D2 are specially designed for its woofer and tweeter. The network properly distributes low,
mid, and high frequencies to the driver components in order to reduce distortion and loss of
sound, thus achieving a naturally balanced sound.
In order to generate powerful, ultra-crisp sound, there are two separate power amplifiers inside
the BX8 D2 for driving the woofer and tweeter separately in a high-end bi-amp structure. The
power delivered to the woofer driver at a low-rated distortion is 40 W, and 30 W is also
delivered to the tweeter.
Rear Panel
1. XLR Input: This jack accepts XLR input
connections with either balanced or
unbalanced wiring. The input wiring of
an XLR connector should be as follows:
XLR Pin 1: signal ground (shield)
XLR Pin 2: signal positive (+)
XLR Pin 3: signal negative (–)
2. TRS Input: This jack accepts 1/4"
connections with either balanced or
unbalanced wiring. For balanced wiring,
a three-conductor TRS plug is
necessary. The input wiring of a TRS
connector should be as follows:
TRS Tip: signal positive (+)
TRS Ring: signal negative (–)
TRS Sleeve: signal ground (shield)
Unbalanced 1/4" wiring can be done with
either a two- or three-conductor (TS or
TRS) plug. A two-conductor (TS) plug
automatically grounds the signal
negative input, whereas a three-
onductor (TRS) plug, wired unbalanced, provides the option of leaving the negative input
open or grounded. We recommend that you ground the unused negative input (this can be
done by wiring the ring and sleeve of the TRS plug together).
The TRS input is summed through a balanced input amplifier with the XLR input, allowing
both inputs to be used simultaneously. Input specifications apply to both.
3. Product Specification: This label contains the model and specification information.
4. Sub-Frequency Vent Port: This port aids in reproduction of very low frequencies by
discharging frequencies below 60 Hz.
5. Volume Control: Use the volume control to set the output sound pressure from the BX8
D2 to proper levels as required.
6. Power Switch: This switch turns the monitor on and off.
7. Power Receptacle: Accepts a detachable 3-circuit line cord in order to power the monitor.
8. Fuse Holder: Holds the external main fuse.
9. Voltage-Select Switch: Provides two selections, 115V AC and 230V AC, and should be
set to match the "house supply" (receptacle) voltage of the country or location in which the
speaker is used. The 115V setting is correct for the USA, while the 230V setting is correct
for most of the UK and Europe.
Frequency Response: 38Hz-22kHz
AC Select
Power
Volume
XLR
TRS
On
Off
LF Amp. Power: 70W / HF Amp. Power:60W
Made in China
220-240V~,50/60Hz 130W
100-120V~,50/60Hz 130W
Input Imp.:20K ohms Bal./10K ohms Unbal.
BX8
D2
Input
1
2
3
4
5
6
7
8
9
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for M-Audio Studiophile BX8 D2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of M-Audio Studiophile BX8 D2 in the language / languages: English, German, French, Italian, Spanish as an attachment in your email.

The manual is 0,65 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of M-Audio Studiophile BX8 D2

M-Audio Studiophile BX8 D2 User Manual - English - 15 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info