707327

M-Audio Oxygen 88 Manual

26
Zoom out
Zoom in
Previous page
1/51
Next page
Oxygen 88 User Guide 25
Setting Trigger Values for the Buttons or the Sustain Pedal
It is possible to set a Trigger Value for a button or the sustain pedal, causing it to send one value when pressed and
held down, and another value when released.
The sustain pedal is already configured to send trigger values by default, ensuring it activates the sustain effect when
pressed and deactivates it when the pedal is released. Buttons can also be configured to operate this way, which
requires four values to be specified. At the example of the sustain pedal, these four values are:
NOTE: When working with proprietary parameters from the 128-255 range, the "Control Assign" setting is used to
configure a button or the sustain pedal for this special mode of operation. This means that certain values that are
usually specified through the "Control Assign" setting must instead be specified via the "Data 1" parameter (such as the
standard MIDI CC parameter in the example below).
The following example will configure a button to "hard pan" the sound to the right speaker when it is held down, and
"hard pan" to the left speaker when it is released. This involves configuring the button to operate as a trigger, while
controlling the Pan parameter (MIDI CC 10):
1. Select a button as described earlier in this guide.
2. Press the Advanced button.
3. Press the Control Assign key.
4. Type 146 using the number keys. This configures the button to operate as a trigger (press/release).
See Appendix B.
5. Press the Enter key.
6. Press the Advanced button.
7. Press the Data 1 key.
8. Type 10 using the number keys. This specifies which parameter the button will trigger and release. In this
example, MIDI CC 10 (Pan). See "Standard MIDI Control Numbers (MIDI CCs)" on page 40.
9. Press the Enter key.
10. Press the Advanced button.
11. Press the Data 2 key.
12. Type 0 using the number keys. This sets the "release" value to zero. In other words, sound will be panned
"hard left" when the button is released.
13. Press the Enter key.
14. Press the Advanced button.
15. Press the Data 3 key.
16. Type 127 using the number keys. This sets the "press" value to the maximum value, so that the sound is
panned hard right when the button is pressed.
17. Press the Enter key.
Key Parameter Value
Control Assign Trigger On/Off operation 146
Data 1 (example) MIDI CC number 64 (Sustain)
Data 2 (example) Button/Pedal Released 0 (minimum)
Data 3 (example) Button/Pedal Pressed 127 (maximum)
TIP: It can be useful to transmit two other specific values instead of sending minimum (zero) and
maximum (127) values as in the above example. When assigning a button to control Pan (MIDI CC 10),
you can, for example, configure Data 2 to send value 38, and Data 3 to send value 93, effectively
causing pan to switch between the approximate "ten o’clock" and "two o’clock" positions when
pressing and releasing the button.
… 26 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for M-Audio Oxygen 88 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of M-Audio Oxygen 88 in the language / languages: English as an attachment in your email.

The manual is 1,54 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of M-Audio Oxygen 88

M-Audio Oxygen 88 Quick start guide - English, German, French, Italian, Spanish - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info