586987

Lynx ONE Manual

9
Zoom out
Zoom in
Previous page
1/36
Next page
Page 9
Please note that with 16 dB of headroom, the LynxONE’s analog outputs are capable
of delivering +20 dBu signal levels. It is important to verify that the equipment you
are driving is capable of handling these signal levels in order to prevent clipping or
possible damage.
Digital Audio
The XLR connectors on the Audio Cable, labeled DIGITAL IN and DIGITAL OUT
are used for AES/EBU and S/PDIF digital audio connections. Connect AES/EBU
devices directly and select AES/EBU Digital Format in the LynxONE mixer application.
Connect to S/PDIF devices using XLR-to-RCA adapters such as the Lynx CBL-
XF2RM18 (female XLR) and the Lynx CBL-XM2RM18 (male XLR). Select S/P DIF
Digital Format in the LynxONE mixer application. Refer to the “XLR Connector Wiring
and Adapters” section for information regarding XLR adapter construction.
MIDI Connections
The 5-pin DIN connectors on the MIDI/Clock Cable are used to connect to the
LynxONE’s two MIDI ports. The MIDI IN 1 and MIDI OUT 1 connectors provide
connections for MIDI port 1. The MIDI IN 2 and MIDI OUT 2 connectors provide
connections for MIDI port 2. Use standard shielded MIDI cables to connect to external
MIDI equipment.
Clock Input and Output
The BNC connectors on the MIDI/Clock Cable, labeled CLOCK IN and CLOCK
OUT are used to synchronize the LynxONE with external equipment. The connectors
support TTL level signals and should be connected with 75-ohm coaxial cable. Connect
the CLOCK IN connector to the clock output of an external device and select External
as the Sample Clock Source in the LynxONE mixer. Adjust the clock Reference to
match the incoming clock type.
CLOCK OUT is a word clock that tracks the sample rate of the LynxONE. Connect
this output to the word clock input of an external device.
Header Connectors
The Header connectors labeled CLOCK IN and CLOCK OUT are used to synchronize
the LynxONE with internal equipment located inside your computer. For systems
containing multiple LynxONE’s, these connectors are utilized to synchronize the sample
clocks of each card. The connectors support TTL level signals and should be connected
using the Lynx Internal Clock Cable or similar 75-ohm coaxial cable.
Connect the CLOCK IN connector to the clock output of an internal device and select
Header as the clock source in the LynxONE mixer. Adjust the clock Reference to
match the incoming clock type.
The signal on the CLOCK OUT header is a word clock that tracks the sample rate of
the LynxONE. Connect this output to the word clock input of an internal device or
another LynxONE.
External Connections
… 9 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Lynx ONE at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Lynx ONE in the language / languages: English as an attachment in your email.

The manual is 0,19 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info