586988
23
Zoom out
Zoom in
Previous page
1/36
Next page
Page 23
Troubleshooting
Audio playback sounds fast or slow when I am using the digital input as
the clock source.
When the digital input is selected as the clock source, the Lynx L22’s sample clock will
run at the sample rate of the incoming digital input signal. In the case when the sample
rate of this signal is 48 kHz and a file being played was actually recorded at 44.1 kHz,
the audio will playback fast. To solve this problem either change the sample rate of the
device driving the digital input or select Internal as the sample clock source using the
Lynx L22 mixer.
How do I minimize record monitor latency when I am doing overdubs?
Use the Lynx L22’s on-board monitor circuitry. This is controlled by the Lynx L22
mixer.
What does the green LED on the Lynx L22 indicate?
When lit, the LED indicates successful initialization of the Lynx L22 and the driver.
When I connect the Lynx L22 analog outputs to the MIC inputs on my
Mackie mixer I hear distortion.
The MIC inputs are being overdriven. Even with the mic gain adjusted to its lowest
setting, the maximum signal level that the MIC inputs of the smaller Mackie mixers
can handle is +14 dBu. In the +4 dBu trim setting, the Lynx L22 is capable of delivering
a +20 dBu signal. To solve this problem use 1/4” line inputs of the mixer. This requires
the use of XLR to TRS adapters as described in the “External Connections” section.
I connect my microphone directly to the Lynx L22 Analog Input
connectors, but the level is very low, what is going on?
The Lynx L22 Analog Input connectors should be connected line level devices only.
To record from a microphone, first route the signal through a microphone pre-amplifier
or mixer and then into the Lynx L22.
Where on the Lynx L22 do I connect my internal CD-ROM drive?
The Lynx L22 has no connector for an internal CD-ROM drive. We recommend using
digital audio extraction software to capture the audio data from your CD’s and saving
it to your hard disk drive as .WAV files. Using this method, the audio files can be
played back using the D/A converters on the Lynx L22 which have far superior
performance to those found in most CD-ROM drives. If your CD-ROM/DVD drive
can reliably extract digital audio then you could use Windows Media Player (Version 7
or higher) to extract digital audio from CDs and play it in real-time with no physical
connection between the Lynx L22 and the CD-ROM drive.
Can I leave my current sound card in my computer while using the Lynx
L22?
You may leave your existing sound card in your computer as long as you have a free
PCI slot and interrupt for the Lynx L22. You may need to reconfigure certain software
to access the Lynx L22 instead of your existing sound card. Please refer to the “Working
with Third Party Applications” section for details.
23


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Lynx L22 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Lynx L22 in the language / languages: English as an attachment in your email.

The manual is 0,15 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info