587002

Lynx Aurora LT-TB Manual

36
Zoom out
Zoom in
Previous page
1/55
Next page
36
The METERS in the Outputs section show the level strength of the signals at the associated
output. The Meters are post-fader, so there will be reduction in Meter level as the signal is
attenuated.
Mutes
The “M” Icon below the fader is for the Mutes. This switch Mutes or UnMutes the associated
output.
When the “M” button is blue like this , then the Mute is ON, and no signal will pass to the
selected output. When the “M” button is gray, like this , then the Mute button is OFF, and
signal CAN pass to the selected output.
Channel Link
In between the two Mute buttons for a pair of Inputs, is the channel link control: . This
control toggles the linked state for a pair of faders and mutes. If two channels ARE linked,
then moving the fader for one of them will move both channels. Similarly, if one is muted
then both will mute. If the faders between the channels are offset, when one is moved the
other will snap to the same position. The linked state also impacts the Pan controls. If one
pan pot is moved to the left the other will move a corresponding amount to the right. For
instance, if the left pot is set to -25, the right channel will pan to +25.
Linked is the default state for pairs of inputs. To “un-link” a pair, click on the link icon and it
will change to a single circle: . In this state, the mute, fader and pan controls operate on a
single channel independently.
Output Button
This identifies the Outputs that are applicable to the fader and mute controls, and is also used
to facilitate routing. As mentioned, the Lynx Mixer uses an Output oriented approach to
routing. Clicking on an Output button, “selects” that output for sources to be assigned to it.
When selected, the button is green. In this state, sources from both the Record and Play panes
can be un-muted, thereby set to stream to the “selected” output.
In the Mixer’s default state, each output has a play device routed to it. For Analog Output
1+2 it is Play 1+2, for analog output 3+4 it is Play 3+4, etc. For Digital Output 1+2 with an
Aurora16, it would be Play 17+18. With an Aurora 8, Digital Out 1+2 would default to Play
9+10.
To add sources to an output, click an output button to select it and it will turn green. Then un-
mute Record and/or Play sources from the Record and Play Panes. Signals from those
sources will now stream to that output. When multiple sources are assigned to a single
output, it is often necessary to attenuate the individual sources to prevent excessive level
from causing distortion to the output.
… 36 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Lynx Aurora LT-TB at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Lynx Aurora LT-TB in the language / languages: English as an attachment in your email.

The manual is 0,99 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info