587002
12
Zoom out
Zoom in
Previous page
1/55
Next page
12
10. Plug in and power up the Aurora using the front panel standby switch. You can see the
LT-TB from the slits in the Aurora top cover. If the green LED on the LT-TB corner (by
the transformer) is flashing, the installation was successful. When a Thunderbolt cable is
connected between the Aurora and a computer, and the driver is loaded, then the LED
will go solid. If the LED does not light, unplug the Aurora and re-mount the LT-TB,
making sure that it is securely attached. Then plug in and power up again. If the green
LED still does not light, please contact Lynx Customer Support.
5.1 Cable Connections
The LT-TB has been tested with standard optical and copper Thunderbolt cables. For Copper
cable, one can use lengths up to 3 meters (9.8 feet). Optical cables, while somewhat more
difficult to acquire, do promise operation with much longer cable lengths, up to 100 meters.
Thunderbolt cables are somewhat unique in that they contain signal transmission electronics.
For this reason it is important to practice good cable management, avoid crimping or
allowing cables to be compressed. If such practices are adhered to, these cables should
provide many years of faithful service.
5.2 Clock Settings and Connections
Please see Section 2.6: Clock Settings and Connections, of the Aurora User Manual for
information about correct clocking of the Aurora within a digital audio system. With an
active Thunderbolt connection, the SYNC SOURCE can ONLY be changed from the Lynx
Mixer application. Generally, SYNC SOURCE should not be changed while an audio
application is open.
On computer boot, or after restoring a Thunderbolt connection, the Aurora will return to the
SYNC SOURCE of last Mixer state. This will be established by hardware ID, so with
multiple Auroras, even if different SYNC SOURCES are established, all should return to the
appropriate last state. It is critical that the Lynx Mixer application is closed before shutting
down the computer, so that the mixer state can be written to a system file for later recall. If
the computer is turned off while the Lynx Mixer is still open, the prior state may not be
restored.
5.2.1 Using the Internal Clock
We recommend using Internal as the SYNC SOURCE for the best clock performance.
In this state, the Aurora can respond to sample rate changes from audio software, but not all
applications will send these rate change requests.
In all compatible versions of Windows, ASIO applications will generally request sample rate
changes to follow the project sample rate, or the rate of the audio being played.
In Windows 7 and Windows 8, MME/DirectSound applications sample rate requests do NOT
get passed down to the audio driver and hardware. Instead they rely upon Sample Rate
conversion built into the operating system to convert the play rate to the rate of the audio
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Lynx Aurora LT-TB at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Lynx Aurora LT-TB in the language / languages: English as an attachment in your email.

The manual is 0,99 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info