708359
16
Zoom out
Zoom in
Previous page
1/24
Next page
Part III: Operating the Wood Chipper
8
PART III: Operating the Wood Chipper
It may be helpful to better familiarize yourself with the features of your Wood Chipper
before beginning the steps outlined in this chapter.
WARNING
A. Read and understand all instructions, safety precautions, and/or warnings listed in
“PART I: General Safety Rules” before operating the WOOD CHIPPER. If any doubt
or question arises about the correct or safe method of performing anything found in
this manual, please contact the dealers in your area.
B. When operating the Wood Chipper, make sure you are standing in the safe operating
area (OPERATOR ZONE). You must stay in the safe operating area at all times when
the ram is in motion (whether extending or retracting). Never place any part of your
body into a position that causes an unsafe operating condition.
C. Before loading and operating the Wood Chipper, always wear protective gear,
including safety goggles, hearing protection, tight-fitting gloves without draw strings or
loose cuffs, and steel-toed shoes.
D. Knowing the correct and incorrect methods of Chipping woods. Never using an
incorrect or unsafe method.
Starting
1. Position your Wood Chipper on flat, dry ground, and then stop the front wheel with
brake, make sure the machine cannot be moved.
2. Make sure the fuel shut-off valve is in the “ON” position.
3. Move the choke control lever to the “CHOKE” position (should only be needed if the
engine is cold).
4. Move the throttle control lever to the “FAST” position.
5. Recoil Start: Turn the Ignition Switch to the “On” position. Grasp the recoil starter
handle and slowly pull until you feel resistance. Let the cord retract a little bit then pull
the cord rapidly to start the engine. One or two pulls usually starts the engine.
6. Electric Start: Turn and hold the Key in the start position until Engine starts then let
the Key return to run position.
7. Move the choke control lever (if used for cold engine) slowly back to the “RUN”
position when the engine is running well.
8. If the Wood Chipper has not been running (cold engine), warm up the engine by
running the engine at half throttle for 3 to 4 minutes, then advance the engine throttle
control to the maximum speed.
16


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Lumag HC15 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Lumag HC15 in the language / languages: English as an attachment in your email.

The manual is 1 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Lumag HC15

Lumag HC15 User Manual - German - 32 pages

Lumag HC15 User Manual - Dutch - 52 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info