Manual Lowrance X-16 (page 6 of 16) (English)

599336

Zoom out

Zoom in

1/16

cable in

the event

a short

occurs.

Crimp

connectors

are

supplied

attach

the fuse

holder to the

power

cable. The red

wire in the

power

cable is the

positive

con-

ductor

The black wire

is the

ground

negative

conductor.

The

graph

protected

from

accidental

polarity

reversals and

damage

will occur if the wires

are reversed.

The unit will not

operate

until the

proper polarity

applied.

FIGURE 3

When

installing

the

power

cable,

you

will find two extra

wires com-

ing

from the

power

cable. The

green

one is for an

optional

Power

Booster and the other

white wire

is for connection to a Loran

receiver If neither of

these fea-

tures are

going

to be

used,

tape

the ends of the

green

and white

wires so that

they

cannot short

Refer to the Advanced

Operation

section for more information

these wires.

TRANSDUCER SELECTION

Lowrance offers

you

the choice

of transducers with

either an 8 or

degree

cone

angle

that will

interchange

with

any

of our 192

kHz sonar units. In other

words,

any

Lowrance

sonar instrument

can be used with

any

Lowrance

transducer of the same

frequency

without

retuning

any kind,

and

no loss of

performance. However,

the use of

any

other manufac-

turer's transducer will result in a

loss of

performance.

Now

you

can select the trans-

ducer

design

and cone

angle

best fit

your

specific

needs. Gen-

erally,

wide cone

angle

transdu-

cers

(20

degrees)

are

ideally

suited for

operating

in shallow

water or at medium

depths.

The

degree

cone

angle

allows

you

to see more of the underwater

world. In 15 feet of water the 20

degree

cone covers an area of

the

bottom thath about 6 feet across.

The 8

degree

transducer covers

only

about a 2 foot circle.

way

to slow the chart

paper

The

chart below

gives

the

range

the

Paper

Save function and the

amount that

each level slows

the

paper.

enable the

Paper

Save

function, simply press

the level of

paper

save

desired,

then

2nd,

then 6. The

paper

should slow

immediately.

For

example,

suppose you

wish to

slow the

paper

down to 1/4 its

present

speed.

Press 3

2nd

6 and the

paper

will now be

traveling

four

times slower than its

speed.

When the

Paper

Save function

enabled,

the X-16 will

PSV=

and the level of

paper

save

that

you

selected. For

example,

our

example

the

Paper

Save value was

3. The X-1 6 will

PSV=3 on the

bottom line of

the chart

paper (See

Figure 45.)

- — --

Lao

34.0

- -

360

48,0

•

60.OFT— rL

LOUPAITCE PSU3

Figure

The

Paper

Save function can

also be used with the

Alternate

Transmit and Print function which

will cut

any Paper

Save

speed

half. This

gives

fourteen different

paper speeds

selectable

the

operator.

To disable the

Paper

Save

function,

simply press

2nd

and the

paper

will

speed up.

PRINT INTENSITY

Three levels of

print intensity

are

provided

for different conditions.

The

stylus printing

can be

adjusted

print lighter

or darker

by using

the Print

Intensity

mode.

When the X-16 leaves the

factory,

the Print

Intensity

is set to level 1.

change

this

setting,

press

the

level of

intensity

desired,

from 0 to

lightest,

2 is

darkest)

and

then

press

2nd

LINES.

For

example,

if the

stylus

printing

too

light, press

2nd

LINES and the

markings

on the

chart

paper

should become

darker

This feature is useful when a

stylus

becomes old.

using

the

'2" level or darkest

level,

the

printing

can

improve. If,

when

using very

slow

paper speeds,

the

record has much

overprint

due to

multiple stylus

strikes in a small

area,

the '0" or

lightest

level can

PAPER SAVE

LEVEL CHART SPEED REDUCED

1/2

1/4

1/5

1/6

FIGURE 4

Co,e

AnSI.

O.pth

7ft

lIlt I

II" 4

III' 11 13

1240 28 7' I

50'

100'

150'

200'

8°at3db

PDF compression, OCR, web-optimization with CVISION's PdfCompressor

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Lowrance X-16 in the language / languages: English as an attachment in your email.

The manual is 0,48 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Lowrance X-16 Manual

Product: