40420

Lowrance LMS 522c igps Manual

235
Zoom out
Zoom in
Previous page
1/252
Next page
225
3. Highlight
FUEL MANAGEMENT and press ENT. Select TANK LOCATION and
press
ENT.
4. Use ↑ ↓ to select the location (Port, Center or Starboard) of the en-
gine interface you want to calibrate and press
ENT.
5. Highlight
FILL TANK and press ENT. The following confirmation mes-
sage will appear: Are you sure you wish to Fill Tank?
6. Select
YES and press ENTER. The following confirmation message will
appear: Do you wish to re-calibrate the device?
7. Highlight
NO and press ENT. Take your vessel out on the water and
burn at least five gallons of fuel. Be sure you run only ONE engine
— the engine connected to your engine interface.
9. Fill up your tank again, noting how much fuel you added to the tank.
Compare that number to the Fuel Used figure displayed on the page
you customized. If the amount of fuel you added to the tank and the
fuel used figure are off by more than 3 percent, we recommend the en-
gine interface be calibrated.
NOTE:
You must use the gauge's Fill Tank command when filling your fuel
tank to keep the engine interface updated with correct information
on the amount of fuel in the tank.
To calibrate a Suzuki Engine Interface:
10. If calibration is necessary, press MENU|MENU, select NMEA 2000 and
press
ENT.
11. Highlight
FUEL MANAGEMENT and press ENT.
12. Select
TANK LOCATION and press ENT to choose the location of the tank
connected to the selected engine interface. Press
ENT.
13. Highlight
FILL TANK and press ENT. The following message will ap-
pear: Are you sure you wish to Fill Tank? Select
YES and press ENT.
14. The following message will appear: Do you wish to re-calibrate the
device? Select
YES and press ENT.
15. Repeat these steps for each engine interface you want to calibrate.
Engine Trim Calibration
Engine Trim is calibrated through the Suzuki Engine Interface Device
Configuration menu.
1. Press
MENU|MENU, select NMEA 2000 and press ENT.
2. Choose
BUS SETUP and press ENTER. Select the Suzuki Engine Inter-
face connected to the desired engine and press
ENT.
3. Highlight
CALIBRATE TRIM and press ENT. The Device Calibration win-
dow will appear with a list of Calibration Instructions.
4. Highlight
START CALIBRATION and press ENT. The following message
will appear: Please fully raise the Engine Trim.
… 235 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Lowrance LMS 522c igps at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Lowrance LMS 522c igps in the language / languages: English as an attachment in your email.

The manual is 6,94 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info