623835
17
Zoom out
Zoom in
Previous page
1/66
Next page
| 15
Display Installation | HDS Gen3 Installation Manual
Flush mounting
Check the template for scaling accuracy, using a tape measure or
ruler against the ruler printed on the template.
Cut away excess paper, and tape down
the template. Check that it is correctly
aligned to a vertical or horizontal
reference. Do not use a bubble level as
vessel may be unlevel! Adjust where
required.
Drill all marked pilot holes, then using an
appropriate saw, cut through the
template and mounting surface, along
the dotted line bordering the shaded
center of the template.
Remove the bezel from the display
by  rst opening the card reader
door. Using a  ngernail or small  at
screwdriver, pull o the bezel at the
slotted points immediately above
and below the card reader. Pull bezel
around keypad forward, till hidden
tab at top right can be disengaged
by a slight downward pull. Applying
a slight twist to top bezel edge will
disengage the top left hidden tab.
The rest of the bezel should come
away easily.
Check the  t of the display, and use a  le to remove any remaining
obstructions. If water-tightness is required, apply a thin, continuous
bead of sealant to the back of the display prior to  nal installation.
Sealant should be of a neutral cure type to prevent damage to the
plastics. Secure the display with the supplied screws. Once screws
are fully tightened, ensure there
is complete contact with the
mounting surface. Lastly, install
the bezel with the card reader
door open; insert the outermost
tabs on the bezel into the slots
on the display, then gently press
down the bezel above and
below the card reader door until
it clicks in to place.
17


Need help? Post your question in this forum.

Forumrules
1

Forum

lowrance-hds-12-gen3

Reset search

  • Hello I have downloaded version 18.2 and have found that this causing some issues on the HDS gen3, Does anyone know how to delete it and down load the old version again? Cheers Rusty Submitted on 24-7-2020 at 08:02

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Lowrance HDS-12 Gen3 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Lowrance HDS-12 Gen3 in the language / languages: English as an attachment in your email.

The manual is 7,44 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Lowrance HDS-12 Gen3

Lowrance HDS-12 Gen3 Quick start guide - English - 8 pages

Lowrance HDS-12 Gen3 User Manual - English - 184 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info