Manual Lowrance GlobalMap 1000 (page 8 of 34) (English)

599373

Zoom out

Zoom in

1/34

DATA INPUT AND OUTPUT

CONNECTIONS

In order for the

GlobalMap

1000

to show

position

information,

requires

navigation

data from

either

Loran-C, Decca,

or GPS receiver than can

send the data in

NMEA 0183 version 1.5 or 2.0 format. If the NMEA

input

is not

used,

then the

Lowrance LGC-1 GPS receiver can be used.

The

wiring

connections for the NMEA 0183 version 1.5 are different than

the ones used

forthe NMEA 0183 version 2.0. If

you

are

using

version

1.5,

then

use

the

green

and black wires on the

GlobalMap's powercable.

you

are

using

version

2.0,

then

you'll

using

the four shielded wires

on the

GlobalMap's

power

cable.

you're using

the

Lowrance LGC-1 GPS

module, simply plug

its

cable

directly

into the

in-line connector on the

GlobalMap's power

cable. This

sends

navigation

data

directly

to the

GlobalMap

without

using any

NMEA

input.

You

can,

desired,

use either NMEA

output

to drive another device

while

using

the LGC-1 as an

input.

The

GlobalMap

1000 also has the

provision

fora

DGPS beacon receiverforuse with the LGC-1 GPS module.

NMEA 0183

VERSION 2.0

INTER FACE

(FOUR

SHIELDED

WIRES)

indicates what the

possible

er-

ror is. This

feature should al-

ways

be reset to zero

(0)

when

finished with that chart.

For

example,

suppose you

are

stopped

at a

location that is

accurately

marked on a

chart.

Your

unit shows a

longitude

position

that is .010

degrees

less than the one on the chart.

Using

the Position Correction

Factor

(PCF)

Offset

feature,

you

makethe unit read the same as the

chart.

you

move,

the unit will

continuously

add the

change

to all

position

displays.

This makes it more

closely

match the datum used

the chart.

For this

reason,

you

should be careful when

entering

the PCF offset. This

offset is saved in

memory.

It doesn't

change

when the unit is turned off.

However,

a Preset does erase the PCF factor.

To set the PCF

factor,

first

press

the MENU

key

two

times,

then

press

the

key

next to the "Datum Translations label.

Finally, press

the

key

next to

the "PCF" label at the bottom of the

display.

The screen shown above

appears.

Nowenterthe correction

foryour

location.

Remember,

this isthe difference

between the location shown on the

present position display

and the

position

shown on the chart. In this

example,

have entered 0 de-

grees,.012

minutes north latitude and 0

degrees,

.068 minutes

east

longitude

as the PCF offset. That is

the

difference

between the

present

position

shown on the unit and our

position

shown

the chart. In other

words,

our

position

shown on the unit is 0.012 minutes south

and 0.068

minutes

of the

position

shown on the chart.

After

you've

entered the desired

offset, press

the

key

next to the "PCF

Mode ON OFF" label. Thisturns the

FCFcorrection

factorthatyou

entered

on. To leave this

screen, press

the CLR

key.

This also

puts

your changes

into effect.

To turn these

changes

off,

return to this screen and

press

the

key

next to

the "PCF Mode ON OFF" label.

Remember, presetting

the unit also

erases

any

PCF

offset,

thereby turning

it off.

TO"P"OONNECTOR

GLOBALMAP 1000

LOWRANCE

OPS MODULE

NMEA

0180

0183

VERSION 1.5

INTERFACE

4 57

PDF compression, OCR, web-optimization with CVISION's PdfCompressor

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Lowrance GlobalMap 1000 in the language / languages: English as an attachment in your email.

The manual is 0,95 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Lowrance GlobalMap 1000 Manual

Product: