522492
6
Zoom out
Zoom in
Previous page
1/22
Next page
6
Traditional Sonar
transducer face is in contact with the hull. Also, make
sure the cable is long enough to reach the sonar unit.
To use shoot-thru-hull installation:
1. Sand the inside surface of the hull, where
the transducer is to be epoxied, and the
face of the transducer. Sand the hull until
it is smooth to the touch. The sanded
area should be about 1-1/2 times the
diameter of the transducer.
2. After sanding, clean the hull and the face
of the transducer with an alcohol wipe to
remove any dust.
3. Apply a thin layer of epoxy (about 1-16”
or 1.5 mm) on the face of the transducer
and the sanded area on the hull. Be
careful when mounting a transducer
inside a boat hull. Once epoxied into
position, the transducer can be very
difcult to remove. Epoxy is available
at www.lei-extras.com (Part No. 106-
98).
4. Press the transducer into the epoxy,
turning it to force out any air bubbles from
under the transducer face. Make sure
there are no
air pockets
in the epoxy
layers.
5. Stop pressing
when it bottoms
out on the hull.
Apply pressure to hold the transducer in
place while the epoxy sets. Be careful not
to move the transducer while the epoxy
is setting. Allow the epoxy to set before
moving the boat.
Epoxy transducer to hull.
HullEpoxy
Apply epoxy to transducer
face and mounting location.
Sand transducer face
and mounting location
0.TWEETY INSTALL_SONAR_DSI.indd 6 9/14/2011 11:55:32 PM
6


Need help? Post your question in this forum.

Forumrules
1

Forum

lowrance-elite-4x-dsi

Reset search

  • Jeg vil ikke bore hul i mit skib, så jeg vil installere transduceren indenbords. den bliver monteret i den styrbords kistebænk, og sat i en klat epoxy. Tyndt lag, og med ledningen fremad mod stævnen, ligesom hvis den var monteret på hækken. Hvor meget signal går jeg glip af ved denne installering? Submitted on 11-10-2022 at 22:45

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Lowrance Elite 4X DSI at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Lowrance Elite 4X DSI in the language / languages: English as an attachment in your email.

The manual is 2,77 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Lowrance Elite 4X DSI

Lowrance Elite 4X DSI User Manual - English - 26 pages

Lowrance Elite 4X DSI User Manual - German - 25 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info