757004
105
Zoom out
Zoom in
Previous page
1/124
Next page
107
User Manual
ing, Date and Time and selects the Cursor Control function.
'MENU' + "ADVANCED SETTINGS" + 'ENTER' + "SIMULATION" + 'ENTER'
SNR = Signal to Noise Ratio
The ratio of the magnitude of a signal that of the noise (interference).
SOG = Speed Over Ground
A calculation of the rate of movement of the ship over the ground.
Speed
The current velocity at which you are travelling, relative to a ground location.
Speed Filter
Turns On/Off the Speed Filter. When it is On, you can filter the speed of the ship, to optimize it. The
default setting is Off.
'MENU' + "ADVANCED SETTINGS" + 'ENTER' + "FIX " + 'ENTER' + "SPEED FILTER" + 'ENTER'
Speed (Simulation)
Sets the value for speed in the Simulation mode. The default setting is 01.0 Kts.
'MENU' + "ADVANCED SETTINGS" + 'ENTER' + "SIMULATION" + 'ENTER' + "SPEED" + 'ENTER'
Speed (Unit)
Sets the speed unit among Kts = knots, Mph = miles per hour e Kmh = kilometers per hour. The
default setting is Kts.
'MENU' + "BASIC SETTINGS" + 'ENTER' + "SPEED" + 'ENTER'
Static Navigation
Sets up a threshold for the speed. When the speed received from the positioning device is under that
threshold, the chart plotter displays zero. The default value is 0.0 Kts.
'MENU' + "ADVANCED SETTINGS" + 'ENTER' + "FIX" + 'ENTER' + "STATIC NAVIGATION" +
'ENTER'
Step Unit (Track)
Choose Distance (Dist) - the chart plotter can store a fix when the distance from its last stored position
is greater than a defined distance; Time - the chart plotter can store a fix after a defined time; Auto - the
software decides when storing a position, on the basis of the straight or curved track. The default
setting is Time.
'MENU' + "ADVANCED SETTINGS" + 'ENTER' + "TRACK" + 'ENTER' + "STEP UNIT" + 'ENTER'
STR = Steering
The difference between COG and CTS. If COG is 25° and CTS is 30°, then STR is 5° Right.
Target
In order to tag on the chart the point, towards which the ship is Heading, you can use a special mark,
called Target. When the Target is placed, all navigation data are referred to this Target (see Par. 3.4,
4.1.1.4, 4.2.1.3, 4.2.2.3).
Inserting Target : place cursor + 'DEST'
Deleting Target (Basic Mode) : place cursor on Target + 'CLEAR'
Deleting Target (Advanced Mode) : place cursor on Target + 'ENTER' + 'DELETE' + 'ENTER'
TD = Time Difference
Loran-C positions are determined by precise timing of the intervals between reception of pulses trans-
mitted by pairs of stations in the selected chain. Between any two stations a ship must be located
somewhere along a line of possible positions where the measured Time Difference, TD, between ar-
rival of pulses from those stations would be observed. The TD is measured from the time of reception
of the master station signal to the time of reception of the slave station signal.
'MENU' + "ADVANCED SETTINGS" + 'ENTER' + "NAVIGATE" + 'ENTER' + "COORDINATE
SYSTEM" + 'ENTER' + "TD" + 'ENTER'
105


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Lorenz MAGNUM PRO at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Lorenz MAGNUM PRO in the language / languages: English as an attachment in your email.

The manual is 3,08 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info