522471
2
Zoom out
Zoom in
Previous page
1/152
Next page
4 User Manual
Warning!
Electronic charts displayed by the chart plotter are believed to be accurate and reliable, but they are not
intended to substitute for the official charts which should remain your main reference for all the matters
related to the execution of a safe navigation.
For this reason we would like to remind you that you are required to carry on board and use the officially
published and approved nautical charts.
Caution
Please read through this manual before the first operation. If you have any questions, please contact the
Company customer service or your local dealer.
The chart plotter is not built water proof. Please give attention to avoid water intrusion into the chart
plotter. Water damage is not covered by the warranty.
Extensive exposure to heat may result in damage to the chart plotter.
Connection to the power source with reversed polarity will damage the chartplotter severely. This damage
may not be covered by the warranty.
The chart plotter contains dangerous high voltage circuits which only experienced technicians can handle.
The C-MAP BY JEPPESEN C-CARD are available from your local dealer.
We will not be liable for errors contained herein, or for incidental or consequential damages in connection
with the performance or use of this material.
Exposure of display to UV rays may shorten life of the liquid crystals used in your chart plotter. This
limitation is due to the current technology of the LCD displays.
Avoid overheating which may cause loss of contrast and, in extreme cases, a darkening of the screen.
Problems which occur from overheating are reversible when temperature decreases.
Warning on Serial Ports Connection
Please be aware that the serial ports are not opto-isolated and then the external device is electrically connected to the
chart plotter. This allows the connection of high speed devices, like Fish Finder. If you are connecting a NMEA0183
device and you would like to isolate it from the chart plotter, you have to add the opto-isolator externally.
Cleaning procedure for the plotter screen
Cleaning of the plotter screen is a very important operation and must be done carefully. Since the surface is
covered by a antireflective coating, the procedure for cleaning all the surfaces can be performed using the
following procedure: You need a tissue or lens tissue and a cleaning spray containing Isopropanol (a normal
spray cleaner sold for the PC screen, for example PolaClear by Polaroid). Fold the tissue or lens tissue into a
triangular shape, moisten the tip and use the index finger behind a corner to move the tissue across the
surface, in overlapping side to side strokes. If the tissue is too wet, a noticeable wet film will be left in its path
and you will need to repeat the process. If too dry, the tissue wont glide easily, and may damage the surface.
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Lorenz COMPACT X7 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Lorenz COMPACT X7 in the language / languages: English as an attachment in your email.

The manual is 2,21 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info