756997
10
Zoom out
Zoom in
Previous page
1/18
Next page
10
User Manual
Lorenz AIS 3000 RT
Power Cable (or Power and Data Cable)
GPS Antenna Cable
VHF Antenna Cable
Installing the AIS 3000 RT unit
WARNING: Do not connect the AIS 3000 RT unit to a mains (line) AC electrical supply, as an electric shock or fire hazard
could result.
CAUTION: Do not connect the AIS 3000 RT unit to a DC supply exceeding 15.6 V or reverse the supply polarity. Damage
to the unit may result.
CAUTION: The AIS 3000 RT unit is designed for operation in the temperature range -25 °C to +55 °C. Do not install (or
use) the AIS 3000 RT unit in environments which exceed this range.
CAUTION: Do not install the AIS 3000 RT unit in an environment where it can be subject to regular exposure to water.
Electrical connections
Warning: Only the RF, data and power cables provided with the AIS 3000 RT unit should be used to connect antennas, power
and display devices so as to maintain the integrity of the enclosure.
Please see the drawings section of this manual for details of the power, data and RF cables supplied.
Remove the top of the transponder unit (eight
screws) as shown.
Using the two co-axial leads supplied connect
the down-lead from a VHF antenna to the VHF
antenna port and connect the down-lead of a
GPS antenna to the GPS antenna port. Please
see Appendix A for recommendations on
antennas and antenna installation.
If an external display unit (chart plotter, PC etc)
is to be used connect the supplied power and
data interface cable to the Power / NMEA port.
If an external display unit is not to be used
connect the supplied power only interface cable
to the Power / NMEA port.
Locate the RF, power and/or data cables into
the rubber grommets pushing them firmly to the
base of each slit. Each cable is pushed into the
grommet slit which lies directly in front of the
connector the cable is connected to.
Replace the top of the transponder unit taking
care to seat the cable grommets and the lid
seal correctly. Do not over-tighten the fixing
screws.
If an external display unit is to be used (such as
a chart plotter, PC serial terminal or other
display device) connect the user end of the
data interface cable to the display device. Note
that the software in the display device must be configured for AIS operation AND to accept standard Class B operation NMEA
sentences. This external display unit software is not part of the AIS 3000 RT transponder package.
27
User Manual
Lorenz AIS 3000 RT
Cable Assemblies
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Lorenz AIS 3000 RT at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Lorenz AIS 3000 RT in the language / languages: English as an attachment in your email.

The manual is 1,06 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info