522457
3
Zoom out
Zoom in
Previous page
1/20
Next page
3
INSTALLATION
GB
Check if the windlass is complete in every parts. If any parts is missing or damaged , please contact your dealer.
TOOLS AND MATERIALS
Drill 11 mm (7/16”), Spanner for M10 nuts
REQUIREMENTS Jig Saw, Power Drill , Silicone Sealant
The electric motor of the windlass is able to operate under spray conditions ; however , if submerged , it could be irreparably damaged.
Ensure there are no deck obstructions. Be sure that there is ample room to enable You to use the handle
(201). In order to facilitate maintenance operations Lofrans suggest to install the windlass on a removable
panel fixed on the deck by bolts.
Deck thickness should be 30 mm (1 3/16”) minimum. If the deck is too thin or inadequate , it will be
necessary to use a backing pad (plywood , timber ) of sufficient dimensions to spread the stress imposed
during recovery of chain. To avoid electrolysis problems do not use stainless steel pad as backing pad.
300 mm
(
11”
)
When the position of the windlass has been set , drill the necessary holes , using the template we supply.
Place the gasket supplied under the base of the windlass. Place the windlass on the deck. The windlass
must be located with the gipsy in line with the bow roller .The chain must turn around the gipsy with a
rotation of 90° approx. Fix the windlass using 3x7/16”UNC or M10 stainless steel hex head bolts. Ensure
the chain locker is of sufficient capacity to store all the chain and leave a minimum of 300 mm ( 11" )
between underside of the deck and the top of the heaped chain. Join the cables to the battery as shown on
the wiring diagram. Introduce the rope/chain into the gipsy , operate the "UP" switch of the foot switch or
remote control and the chain will automatically be fed into your locker. Take care to keep hands and feet
well clear of incoming chain. If the windlass runs in wrong direction , change over M1 and M2 cables at
the control box.
After using the windlass , we strongly recommend that the nuts are checked again to ensure they are
well tightened.
www.busse-yachtshop.de | info@busse-yachtshop.de
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Lofrans Dorado at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Lofrans Dorado in the language / languages: English, German, French, Italian, Spanish as an attachment in your email.

The manual is 0,94 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info