475109
133
Zoom out
Zoom in
Previous page
1/164
Next page
Connect ID 32-55 - 133 -
Operating instructions
Automatic update via the internet
Your TV set checks at definite intervals whether a newer software than
the one installed in the TV set is available in the Internet. If this is the
case, you can find this out by a screen message.
Showing/Hiding information on new software
MENU: Call TV menu.
3 4 Select Settings,
6 go to the menu line below.
3 4 Select Miscellaneous,
6 go to the menu line below.
3 4 Select Software update,
6 go to the menu line below.
34 Select Via the internet,
6 go to the menu line below.
3 4 Select Inform about new software.
6 go to the menu line below.
34 Select yes / no.
OK Adopt.
New software found
Yes is selected for Inform about new software.
If the TV set has found a new software version during the check, you
will be informed about this via a screen message.
5 6 Select the desired procedure.
After confirmation, the new TV software will be loaded
from the internet and then programmed.
For more information see left column.
The software will be loaded and programmed after the
TV set has been switched off into standby mode for the
next time. The display on the control panel (see
page 10) will light up yellow during the update.
The TV set must not be switched off at the mains before
the downloading process is complete (control panel
display lights up red)!
Loading the software will be postponed to a later date.
The new software message will be displayed the next
time the TV set is switched on.
If the loading process is postponed three times then the
message will only be shown again once the next soft-
ware version is available.
The new software will not be loaded. The on-screen
message will only be shown again for the next software
version.
TV MENU
Settings
Miscellaneous
Software update
Via the internet
Inform about new software
yesno
Load the
software now
Load software
when
switching off
to standby
Load software
later (max.
3 times
notification)
Do not load
this software
version
Load new software package
Only the parts of the software package that are not up
to date will be automatically downloaded from the inter-
net and updated.
Each part of the software is downloaded individually from
the internet and is then programmed.
The total time required for all the software parts to be
downloaded from the internet is dependent on the speed
of data transfer that is being used.
The total loading and programming process can take up
to 50 minutes in total.
Please do not switch off your TV set at the mains during
the entire loading and programming process.
You will be informed once the loading and programming
process is complete.
To make your TV set completely ready for use again,
please turn it off and on again at the mains.
SOFTWARE UPDATE
The "TV base software" is being programmed, please wait ...
Note:
The total time required for the loading process from the internet is dependent
on the type of data transfer that is being used:
- up to 125 minutes over a modem (56k)
- up to 110 minutes over ISDN (64k)
- up to 5 minutes over DSL (DSL2000).
The loading and programming process can take up to approx. 50 minutes
in total.
Please do not switch off your TV set at the mains during the entire loading
and programming process.
SOFTWARE UPDATE WIZARD
The software package has been loaded successfully.
Please switch the TV set off and back on at the mains switch to ensure it is fully
operable.
n
Software update
133


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Loewe Connect ID 40 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Loewe Connect ID 40 in the language / languages: English as an attachment in your email.

The manual is 48,06 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Loewe Connect ID 40

Loewe Connect ID 40 User Manual - German - 162 pages

Loewe Connect ID 40 User Manual - Dutch - 164 pages

Loewe Connect ID 40 User Manual - French - 52 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info