475109
26
Zoom out
Zoom in
Previous page
1/164
Next page
Connect ID 32-55 - 26 -
Operating instructions
Setting options for the satellite system
(max. 4 satellites on DiSEqC multiswitch):
5634 Select and adapt settings for the DiSEqC
multiswitch.
The refresh rate determines how often a DiSEqC
command is output. A refresh is only necessary with
cascaded systems.
The control voltage controls the switching of the
polarisation level (horizontal/vertical) in non-DiSEqC
capable components (e.g. control of single LNBs via
DiSEqC multiswitch).
The 22kHz signal controls the switching between high
and low band in the Band setting. The Position setting
controls the selection of the satellites in non-DiSEqC
capable components.
The Toneburst controls the selection of the satellites in
non-DiSEqC but toneburst capable components with
the Position and Option settings.
OK Proceed
5 6 Select Satellite 1 ... Satellite 4,
4 select satellites from list,
OK Proceed.
5 6 Select network.
If several networks are available over DVB-S, you
can decide which network you want to receive
your channels from.
OK Proceed.
34 Set LNB frequencies.
You do not normally need to change the values.
OK Proceed.
(with Setting options for DVB-S reception (contin-
ued) on page 27).
OK
INITIAL INSTALLATION (DVB-S)
Repeat rate none 1 2
Control voltage 13/18V on
22kHz signal Band
Toneburst off
FIRST INSTALLATION WIZARD
With the refresh rate you determine how often a DiSEqC command is output.
This is only necessary in a cascaded system. Your system provider will be able
to tell you more about this.
Proceed Back
OK
INITIAL INSTALLATION (DVB-S)
Satellite selection
Satellite 1 Astra1 19,2°E ...
Satellite 2 Hot Bird 13°E
Satellite 3 Eutelsat W2 16°E
Satellite 4 none
FIRST INSTALLATION WIZARD
Please specify which satellites you want to receive.
Proceed Back
OK
FIRST INSTALLATION WIZARD
Please state from which network you wish to receive your station.
Proceed Back
INITIAL INSTALLATION
Network selection
other network
CanalDigitaal
OK
OK
INITIAL INSTALLATION (DVB-S)
LNB frequencies
ASTRA1 19,2°E Low band 9750 MHz
ASTRA1 19,2°E High band 10600 MHz
Hot Bird 13°E Low band 9750 MHz
Hot Bird 13°E High band 10600 MHz
Eutelsat W2 16°E Low band 9750 MHz
Eutelsat W2 16°E High band 10600 MHz
FIRST INSTALLATION WIZARD
If the LNB is designed for a low (low band) and high (high band) reception range,
enter both frequencies (e.g. 9750 and 10600 MHz). Otherwise enter only one of
the frequencies (e.g. 9750 MHz). If necessary, this will have to be done for
several satellites.
Proceed Back
DiSEqC one
cable
communal
system
Satellite
selection
Network
selection
LNB
frequencies
Manual
registration
(for socket
ANT SAT)
Transmission
channel/
frequency
PIN protection
Settings
DiSEqC
multiswitch
Repeat rate
Control
voltage
22kHz signal
Toneburst
Satellite
selection
Network
selection
LNB
frequencies
Setting options for the satellite system
(DiSEqC one cable communal system):
56 Select DiSEqC single cable communal installation.
OK Proceed.
4 Select satellites from list,
OK Proceed.
5 6 Select network.
If several networks are available over DVB-S, you
can decide which network you want to receive
your channels from.
OK Proceed.
34 Set LNB frequencies.
Normally, you do not need to change the values
for high and low band, unless the LNC (LNB) of
your satellite system uses a different oscillator
frequency (important for the frequency display).
OK Proceed.
5634 Select and adjust settings for the DiSEqC single
cable communal installation.
Select the desired transmission channel and the corre-
sponding transmission frequency.
If your system is designed for it, it is possible to protect
your used transmission data from use by other subscrib-
ers with a PIN.
OK Proceed.
(with Setting options for DVB-S reception (contin-
ued) on page 27).
OK
OK
INITIAL INSTALLATION (DVB-S)
Select DiSEqC single cable communal installation
DELTA SUM-514
DELTA SUM-516
DELTA SUM-518
DELTA SUM-918
DELTA SUM-928
KATHREIN EXR-551
KATHREIN EXR-552
KATHREIN EXR-501
FIRST INSTALLATION WIZARD
Please enter here which DiSEqC single cable system you are using. The following
setting parameters of your system are then adapted accordingly.
Proceed
OK
FIRST INSTALLATION WIZARD
Please specify which satellites you want to receive.
INITIAL INSTALLATION (DVB-S)
Satellite selection
Satellite 1 Astra1 19,2°E ...
Proceed Back
OK
FIRST INSTALLATION WIZARD
Please state from which network you wish to receive your station.
Proceed Back
INITIAL INSTALLATION
Network selection
other network
CanalDigitaal
OK
OK
FIRST INSTALLATION WIZARD
If the LNB is designed for a low (low band) and high (high band) reception range,
enter both frequencies (e.g. 9750 and 10600 MHz). Otherwise enter only one of
the frequencies (e.g. 9750 MHz). If necessary, this will have to be done for
several satellites.
Proceed Back
INITIAL INSTALLATION (DVB-S)
LNB frequencies
Low band 9750 MHz
High band 10600 MHz
OK
FIRST INSTALLATION WIZARD
Please log in to your DiSEqC single-cable system which is connected to
the ANT SAT antenna input abd state the desired transmission channel and
the corresponding transmission frequency. If you antenna system is designed
for it, it is possible to protect your transmission data from being used by other
users with a PIN.
INITIAL INSTALLATION (DVB-S)
Manual registration (for socket ANT SAT)
Transmission channel 1 2 3 4 5 6
Transmission frequency 1284
PIN protection no
Define/change PIN 0000
Proceed
OK
n
Initial installation
26


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Loewe Connect ID 40 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Loewe Connect ID 40 in the language / languages: English as an attachment in your email.

The manual is 48,06 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Loewe Connect ID 40

Loewe Connect ID 40 User Manual - German - 162 pages

Loewe Connect ID 40 User Manual - Dutch - 164 pages

Loewe Connect ID 40 User Manual - French - 52 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info