645576
14
Zoom out
Zoom in
Previous page
1/227
Next page
Loewe bild
User handbook
14
Connecting the TV set
Connecting to the mains supply
Remove the cover for the connections.
Connect the TV set to a 220-240V mains socket:
With built in mains cable: Connect the mains supply plug of the mains
supply cable attached to the TV to a power outlet.
With external mains cable: First plug the smaller plug (small set plug)
of the mains supply cable into the mains supply connector (AC IN)
of the TV set and then connect the larger plug (Euro plug) to a mains
supply socket.
Connecting antennas
(1
Cable (analogue)/DVB-C/DVB-T antenna:
Plug the cable of antenna, cable TV system or room antenna into the
ANT TV socket.
If you want to use analogue cables/DVB-C connection and a DVB-T
antenna together, use an external antenna switch (available from
your dealer).
Satellite antenna DVB-S:
Depending on the used satellite system, connect a connecting cable
from the multi-switch or directly from the LNC to the ANT SAT1 and
ANT SAT2 sockets of the TV set respectively.
When connecting the TV set to a single cable community antenna,
connect the ANT SAT1 and ANT SAT2 sockets directly to the
appropriate SAT antenna socket.
AC IN
ANT
TV
ANT
SAT1
ANT
SAT2
R TV
Cable
analogue /
DVB-C
DVB-T DVB-S
When connecting the TV set to a DiSEqC single cable community
antenna (in accordance with EN 50494), connect the ANT SAT1
socket directly to the appropriate SAT antenna socket.
For a DiSEqC single-cable shared system, you only need in principal
only one antenna cable. The further sub-division of the signal to
the two reception pathways is transferred by the satellite tuner of
the TV set.
If you want to use two transmission channels of the DiSEqC single-
cable shared system (for example, for different channels main
picture / PIP picture), both channels are received on a SAT antenna
cable.
In the antenna configuration one antenna cable must be provided.
It is possible to reuse an existing SAT cabling with two connection
cables on a DiSEqC single-cable shared system. However, the
system components used (sockets, distributors, etc.) must be
designed for DiSEqC operation.
If you want to use two channels of the DiSEqC single-cable shared
system (for example, for a different channels main picture / PIP
picture), then one channel will be received per SAT antenna cable.
In the antenna configuration, two antenna cables and the number
of used channels thus also must be set to “two“ .
Ask your dealer in this regard.
Connecting the TV set to the Home network
You may link your TV set to the home network by a wired connection
(Ethernet, Powerline adapters separately available) or by a wireless
radio connection (WLAN). For wireless connections, the TV set has
an internal WLAN antenna.
In order to play back data from your home network your Loewe TV
supports the UPnP AV standard.
You call the network wizard to configure the network adaptor (System
settingsטMultimedia/NetworkטNetwork settingsטNet-
working).
Under no circumstances may the TV set be wired and at the same
time connected by a wireless connection to the same network, e.g.
router. This may cause severe operational faults!
Example for a wired connection
Connect the LAN socket of your TV set to the LAN switch/router of
your home network with a network cable (available from your dealer).
DSL
LAN
LAN switch/router
TV set
PC
Preparing the TV set
(1
Availability varies by device type (see chapter Technical data - equipment features for your TV set).
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Loewe Bild 1.40 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Loewe Bild 1.40 in the language / languages: English as an attachment in your email.

The manual is 10,9 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Loewe Bild 1.40

Loewe Bild 1.40 Quick start guide - English - 14 pages

Loewe Bild 1.40 User Manual - German - 225 pages

Loewe Bild 1.40 Quick start guide - German - 14 pages

Loewe Bild 1.40 User Manual - Dutch - 224 pages

Loewe Bild 1.40 Quick start guide - Dutch - 14 pages

Loewe Bild 1.40 Quick start guide - French - 14 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info