548740
115
Zoom out
Zoom in
Previous page
1/154
Next page
Art 40-60
User guide
115
System settings
Connections
Antenna DVB
Here you can make settings for the DVB-T antenna and call the antenna
wizard for the DVB-S antenna.
Call Antenna DVB
HOME: Call Home view.
 Mark System settings,
OK call System settings.
 Mark Connections,
go to next column.
 Mark Antenna DVB,
go to next column.
 Select the desired setting,
 call.
Explanations of the setting options in the antenna DVB menu:
Antenna
DVB-S
Here the antenna wizard starts guiding you through
all the settings relevant to the DVB-S antenna. The
settings of the DVB-S antenna wizard are explained
in the procedure of initial installation.
Antenna
DVB-T
Here you can set whether your DVB-T antenna needs
a supply voltage.
Antennas with an integrated amplifier need a supply
voltage on the antenna line. In this case, select Sup-
ply voltage 5V and confirm with OK.
Otherwise, select No supply voltage and confirm
also with OK.
Positioning/aligning DVB-T antenna
If you are receiving one or more DVB-T stations with picture and sound
interference then you should change the installation location and
alignment of the antenna. Ask your dealer to tell you which channels
are used to broadcast the DVB-T stations in your region.
A DVB-T station is received and selected.
Calling manual search (see chapter System settings, section Stations
– Manual TV/Radio scan).
Due to the preset stations, the signal source is already selected as
DVB-T. Position and align the antenna so that maximum C/N values
and levels are reached.
Search for DVB-T stations one after the other and compare values for
C/N and Level. Then position/align the antenna to the weakest station
so that maximum values for C/N and Level are obtained. The value
for BER should be as low as possible.
Thereafter, perform an automatic search for all DVB-T stations.
...
Antenna DVB
Antenna
DVB-S
Antenna
DVB-T
The following antenna wizard guides you through all the
necessary settings relevant to your antenna system.
AV connection settings
In the AV connection settings menu the parameters for the AV con-
nection socket can be adapted.
Calling the connections menu
HOME: Call Home view.
 Mark System settings,
OK call System settings.
 Mark Connections,
go to next column.
 Mark AV connecting settings,
go to next column.
 Select the desired setting,
 call.
Explanations of setting possibilities in the AV connecting settings
menu:
Device at
connection
AV
Indicate here whether a set and, if yes, which one is
connected to the AV socket.
Signal type
You set the signal type of the device connected to AV
or AVS here. Normally, you should leave the setting to
Automatic VHS/SVHS; otherwise select a suitable
signal type. You can find out more from your dealer.
Allow
switching
voltage
If this function is activated, the video and audio of an
external unit connected to the AV connector (not at
AVS) will immediately be reproduced on all TV broad-
cast sites when playback is started up, provided that
the external unit supplies a switching voltage.
...
AV connect-
ing settings
Signal type
Please input whether a device is connected to the AV
socket and if so, which device.
Allow switch-
ing voltage
115


Need help? Post your question in this forum.

Forumrules
1

Forum

loewe-art-50

Reset search

  • When switching on, it takes 3 to 4 cycles of manual switch before finally switched on Submitted on 26-2-2017 at 09:37

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Loewe Art 50 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Loewe Art 50 in the language / languages: English as an attachment in your email.

The manual is 6,37 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Loewe Art 50

Loewe Art 50 User Manual - German - 154 pages

Loewe Art 50 User Manual - Dutch - 46 pages

Loewe Art 50 User Manual - French - 154 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info