645603
13
Zoom out
Zoom in
Previous page
1/144
Next page
Art 40-55
User manual
13
Switching the TV set ON/OFF
Switching TV set to the standby mode
Switch the mains switch on the bottom side of the device to position I.
The indicator in the control panel on the front side lights up white. The
set is now in standby mode.
Switching the TV on/off on the control unit
To switch the TV set into Operating mode or switch it off into Standby
mode, press the middle of the On/Off button.
By pressing one of the buttons on the control panel, the TV set can also
be turned on. Using the keys M/+/- you switch the TV set to TV mode
and to radio mode when using the R key.
Meaning of the colour of the LEDs in the On/Off button:
white: TV set in standby.
Depending on the ambient brightness, the
white LED display is dimmed
(1
and lights
up with a different degree of brightness.
If the TV set is in quick start mode, the
white LED display is not dimmable and
starts with full brightness.
white, intermittent:
TV set starts.
green: TV set switched on.
red: timer recording active.
blue:
TV set in standby and background operation
active (EPG data updating, software
update).
After switching on the TV set, it takes a few seconds for further
operating commands to be processed (Exception: Quick start
mode, see chapter System settings, section Control – Quick
start mode). Your TV set is ready to operate as soon as the status
indicator in the control panel lights up in green.
M
R
+
-
Switching the TV set on by means of the remote control
Press the on/off key.
Or:
Press the TV key.
The previously watched station will be called.
Or:
Press numerical keys 1-9.
The corresponding station will be called.
After switching on the TV set, it takes a few seconds for further
operating commands to be processed (Exception: Quick start
mode, see chapter System settings, section Control – Quick
start mode). Your TV set is ready to operate as soon as the status
indicator in the control panel lights up in green.
Switching the set off with the remote control (Standby)
Press the on/off key.
Before switching off the set with the mains switch,
we recommend you to switch it to standby mode.
Switching off the TV set and connected additional devices
(System standby)
Press on/off key long:
Switch TV set and all CEC-capable devices connected
to the HDMI interfaces OFF to Standby mode (System
Standby).
Quick start mode
If you enable the Quick Start Mode and you switch on the TV set from
standby, the TV picture can be immediately seen without delay. You
can specify the times at which your device will be in the Quick Start
Mode. Please note that in this case you will have a higher energy
consumption.
You can find the Quick Start Mode under System settings ט Control
ט Quick start mode.
Default setting for the Quick Start Mode: off
.
Technical information
Switching off the TV set with the mains switch during operation or an
inadvertent disruption to the power supply (e.g. power failure) can
cause damage to the hard disk file system of an externally connected
hard disk and hence loss of the recorded broadcasts.
Before switching off the set with the mains switch, we recommend
you to switch it to standby mode.
However, if unexpected problems occur when operating the hard
disk, formatting the external hard disk may rectify this. Refer to the
instructions in chapter System settings, section Control – Hard
disks.
Loewe are not liable for the loss of data on the hard disk externally
connected to your TV set. To avoid data loss, we recommend copying
important recordings to an additional external storage medium.
Switching the TV set ON/OFF
Control unit
Mains switch
Display
(1
Automatic dimming depending on the room brightness (OPC) must be activated (see chapter System settings, section Picture).
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Loewe Art 48 - SL3 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Loewe Art 48 - SL3 in the language / languages: English as an attachment in your email.

The manual is 6,75 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Loewe Art 48 - SL3

Loewe Art 48 - SL3 Quick start guide - English - 50 pages

Loewe Art 48 - SL3 Quick start guide - German - 50 pages

Loewe Art 48 - SL3 User Manual - German - 146 pages

Loewe Art 48 - SL3 Quick start guide - Dutch - 50 pages

Loewe Art 48 - SL3 User Manual - Dutch - 145 pages

Loewe Art 48 - SL3 Quick start guide - French - 50 pages

Loewe Art 48 - SL3 User Manual - French - 145 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info