813544
6
Zoom out
Zoom in
Previous page
1/16
Next page
6
Min: 450
Min: 300mm
Min: 300mm
Min: 1800mm
Max: 900
BASE
WALL
CEILING
WALL
WALL MOUNTING:
1. Measure and fasten so that the wall brackets are attached at a distance of
530 mm (centre holes).
2. Install the opposite bracket, but refrain from tightening the nuts.
3. Lift the heater to the height of the brackets. Then connect the two
brackets using M8 nuts and M8 rail screws.
4. Tilt the heater until it is at the desired angle. Then tighten all nuts.
Make sure, however, that it is not tilted at an angle greater than 45
degrees, otherwise the tilt sensor will prevent operation, and the error
code E2 or 23 will be displayed.
Important - The LED display must always be situated on the left side of
the device during installation. If the display is on the right, incorrect,
side, the error code E2 or 23 will be displayed, and operation will not be
possible.
OPERATING THE HEATER
To switch the heater on, press the on/off switch on the underside of the
device, so that the display shows „0“.
Press the temperature control on the front, the highest heating level 4
starts immediately. Press the temperature button followed by the arrow
keys on the remote control to set the desired heating level.
Press the timer button and then use the arrow buttons to set the time until
the automatic switch-off.
To return to standby mode, press the Standby Mode button on the remote
control.
Press the Sensor button on the remote control to set the motion sensor
mode. When motion is detected, the heater turns on for 15 minutes. If
no further movement is detected during these 15 minutes, the heating
element switches off (during this mode the display shows A-). If no
movement is detected in this mode for an hour, the heater switches to
normal standby mode.
To reactivate the motion sensor mode, press the motion sensor button on
the remote control again.
Pressing on the LEVEL button takes you straight to the highest heating
level.
To switch off the heater, press the on/off button on the underside of the
device.
LED DISPLAY
ON/OFF BUTTON
TEMPERATURE
REGULATOR
BATTERY
COMPARTMENT
REMOTE CONTROL
ON/OFF BUTTON
LEVEL
+
-
BATTERY REPLACEMENT
Press the battery compartment button and slide out the battery holder.
Remove the old battery and insert the new one. Make sure that the
positive pole of the battery is facing upward. Use only CR2025 or CR2032
batteries with the remote control.
Push the battery holder back into the remote control, until you hear it click
into place.
Note: Always take care to ensure that no water or other liquids ever enter
the remote control.
CLEANING AND MAINTENANCE
Always disconnect the heater‘s power supply and allow the device to cool
down before performing any maintenance work.
DO NOT operate the device if dust or dirt has accumulated in or around the
heater.
The heater is maintenance-free and can only be cleaned externally.
Use a damp cloth to clean the exterior surfaces. DO NOT use strong,
aggressive or soluble cleaning agents when cleaning the heater, as these
may damage the plastic parts.
If the heater is removed from the holder due to an extended period of non-
use, always keep it in a protected, dry and childproof place.
Do not touch the heating element with your bare fingers.
Never attempt to repair or adjust the electrical or mechanical functions of
the heater.
If the power cable is damaged, cease using the device.
TECHNICAL DATA
Model SNBHTR_UK
Voltage (V) 220 - 240V AC, 50/60 Hz
Power (W) 2000W
Splash protection IPX4
Dimensions W x H x D (mm) 900 x 130 x 90
Weight (kg) 2,6 kg
Remote control Battery: 1 x CR2025
Power: 3V
ENVIRONMENTAL INSTRUCTIONS
Do not dispose this product at the end of its service life through
normal domestic waste. It has to be disposed through a collection
agency that recycles electric and electronic devices. This is
pointed out by the symbol on the product, in the instruction
manual, and on the packaging. Please inquire about local
collection agencies that may be operated by your distributor or your
municipal administration. By recycling, making use of the materials, or other
forms of recycling old units you are making an important contribution to
protecting our environment.
This product complies with the European directives.
M23725_M23726_LivingtonInstantHeater_Manual_20210504_CP.indd 6M23725_M23726_LivingtonInstantHeater_Manual_20210504_CP.indd 6 10.05.21 08:2610.05.21 08:26
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Livington M23725 InstantHeater at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Livington M23725 InstantHeater in the language / languages: English, German, Dutch, French, Italian as an attachment in your email.

The manual is 2.4 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info