Manual Livington iRon 140903 (page 8 of 32) (English, German, Dutch, French, Italian, Turkish, Spanish)

703165

Zoom out

Zoom in

1/32

ture control lamp can light up periodically as the iron

keeps itself at a constant, set temperature.

TIP: The following temperature settings are available:

80-120°C using position 1 / •

120-160°C using position 2/ ••

160-200°C using position 3/ •••

180-230°C using position MAX

Always iron textiles following the manufacturer’s direc-

tions.

Sym-

bol

Mate-

rial

Tem-

pera-

ture

Steam Jet

steam

Spray

functi-

Syn-

thetics/

silk

x x

✓

Wool

✓

Cotton,

linen

MAX

✓ ✓ ✓

Tip: this symbol means „Do not iron“

✓- can be used.

x - cannot be used.Ironing

a) Using the cable

1. Set the cable mode button to

(corded ironing – il-

lustration K)

2. Lift up from the base station and iron with the cord

attached

3. As soon as you have finished ironing, unplug from the

power supply, let the iron cool down fully and then

store it in a dry place

b) Cordless

1. Set the cable function button to

(cordless ironing

– illustration M) and the iron will separate from the

corded unit.

2. Lift up the iron from the base station and iron without

the cable unit attached.

3. After approx. 10 seconds replace the iron onto the

charging station so that it does not cool down below

the temperature setting. The high-performance heat

and steam reservoir of the Livington iRon recharges

within 5 seconds. Typically when you use an iron,

you iron approximately every 10 seconds. It takes 5

seconds to move the garment. This is exactly the time

the Livington iRon needs to recharge and reach tempe

rature. You should therefore always replace the iron in

the station while you move a garment.

IMPORTANT: Should you stop ironing for a while, always

put the iron back on the base station to allow it to heat

back up again.

The less often you use the shot of steam function, the

longer you will be able to iron in cordless mode, without

needing to heat the iron back up again. We therefore

recommend corded ironing if you need to use the shot of

steam function very regularly.

4. As soon as you have finished ironing, unplug the cable

from the mains and allow it to cool down completely

and store it afterwards in a dry place.

Nano-ceramic easy glide sole plate

The scratch-resistant Nano-ceramic easy glide sole plate

provides the best possible care for your textiles. Heat is

stored for longer, enabling you to effortlessly smooth out

creases on different items of clothing.

Steam and spray functions:

Shot of steam (illustration E)

By pressing the shot of steam button, steam is imme-

diately released to help remove tough creases. Please

check that there is a sufﬁcient amount of water in the

water tank.

By using the steam controller (illustration G), you can set

the desired amount of steam required. When set to “off“,

you can iron without steam.

The shot of steam function can also be used when

holding the iron in a vertical position. Take care never to

direct steam at people or animals.

The shot of steam function can only be activated at

temperatures between •• and MAX.

This iron is equipped with an anti-drip function: at very

low temperatures, steam production is automatically in-

terrupted so that no water can drip out of the sole plate.

Spray button (illustration F)

On pressing the spray button, a ﬁne cloud of spray is

produced to dampen difﬁcult to iron textiles. If required,

press the spray button several times to ensure that the

item of clothing is damp enough. Check that there is a

sufﬁcient amount of water in the water tank.

Textile brush

1. Place the textile brush attachment onto the ironing

board and push the iron onto the textile brush attach

ment. (illustration Q). Warning: there is the risk of

burns, as the sole plate of the iron gets very hot.

2. To remove the textile brush attachment, use the hook

at the tip of the textile brush. Clamp the hook at the

tip of the textile brush attachment and carefully pull

textile brush attachment from the iron’s sole plate.

(Illustration R)

WARNING: there is the risk of burns as the soleplate of

the iron and the textile brush attachment can get hot.

CLEANING AND MAINTENANCE

After ironing

1. Unplug the appliance and let the iron cool down fully

2. Empty the water tank. Clean the sole plate using a

damp towel and a non-foaming (fluid) cleaning agent

to remove calk and other impurities.

3. Clean the casing with a damp towel.

4. Keep the empty iron upright on a secure surface.

You may wish to protect the iron plate with a piece of

material.

Self-cleaning function

1. Fill the water tank with water, set it to the highest tem

perature and plug it into an electrical socket. Check

that the steam controller is set to ”off”.

2. The temperature control button lights up. As soon as it

has gone out, hold the iron over the sink and turn the

steam control backwards using a little pressure. Steam

and boiling water will flow out of the sole. Impurities

and calk droplets are rinsed away.

Gebrauchsanleitung140903.indd 8 19.02.15 18:00

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Livington iRon 140903 in the language / languages: English, German, Dutch, French, Italian, Turkish, Spanish as an attachment in your email.

The manual is 1,09 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Livington iRon 140903 Manual

Product: