742166

Livin Flame Leeds Manual

15
Zoom out
Zoom in
Previous page
1/24
Next page
ENG-3
Getting started
- Remove the appliance from the box.
- Remove any packaging from the product.
- Place the packaging inside the box and either store or dispose of safely.
Contents of Carton
- Electric wall mount replace
- Wall xing bracket
- Fixing screws and wall plugs
- Remote control
- Instruction Manual
- Imitation re blocks
Helpful Advice Before Fitting
- Please retain all packaging until you have checked and counted all the parts and the contents of
the xing pack against the parts list.
- Do not use this appliance if any part has been under water. Immediately call a qualied
service technician to inspect and to replace any part of the electrical system if necessary.
- Keep little children away before and during installation. Be aware that the little children do not
be in contact with the parts.
- The electric replace can be installed almost anywhere in your home. Please, read and follow the
instructions carefully by choosing a location. For the best result, install the electric replace not in
direct sunlight.
Tools required
- Magnetic Phillips Screw Driver
- Drilling machine
Installation
- It’s recommended at least 2 or more people install the replace.
- Do not switch the appliance on until it properly installed as described in this manual.
- Please note that before the electric replace will be installed on the wall, care must be taken not
to damage concealed cables.
- The electric replace should be located close to a suitable mains socket to enable connection. The
electrical socket must be easily accessible to allow disconnection.
- A height of 600mm from bottom of heater to oor is recommended for optimum viewing of
fuel bed.
- Minimum distance:
Sides 200 mm
Floor 350 mm
Ceiling 200 mm
Wall 0 mm
- Choose a solid and plain wall and then stick the template on the position where you want to install
the replace. (Picture 2)
- Drill the marked position using a suitable sized drill bit for the chosen xings. (Picture 3)
- Install the 2 top hanging swell plug into the wall and then install the 2 long screws. (Picture 4)
- Fix the lower support bracket on the heater. (Picture 5)
- Locate the heater onto the 2 top hanging swell plug and secure the lower support bracket using 2
long screws. (Picture 6)
- Remove the template paper.
- Put the log or pebble stones on the fuel bed.
- Select the right fascia and then Install it onto the re as the picture.
- Lock the fascia bracket with 2 short screws by screw driver as the picture.
Picture 1
… 15 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Livin Flame Leeds at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Livin Flame Leeds in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 1,88 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info