To reduce the likelihood of serious head injuries, install shock-absorbing protective surfacing under and around this unit. The protective surfacing should be
applied to a depth suitable for the unit height in accordance with ASTM F1292. Follow the guidelines below for each type of surfacing:
• DO NOT install this unit over concrete, asphalt, packed earth, grass,
carpet, or any other hard surface. A fall onto a hard surface can result in
serious injury to the user. Grass and dirt are not considered protective
surfacing because wear and environmental factors can reduce their
shock-absorbing eectiveness. Carpeting and thin mats are not
adequate protective surfacing.
*Ground level equipment, such as a sandbox, activity wall, playhouse or
other equipment that has no elevated play surface, does not need any
protective surfacing.
• PLEASE REFER TO CRITICAL FALL HEIGHT INFORMATION.
• This unit should be installed on a level surface by an ADULT with an
ADULT ASSISTANT. Place the unit on a at area to minimize ground
preparation.
• Choose a level location for this unit to reduce the likelihood of the play
set tipping over and loose-ll surfacing material washing away during
heavy rains.
• Place this unit no less than 6 feet (2 meters) from any structure or
obstruction, such as a fence, garage, house, overhang, branches,
laundry lines, or electrical wires.
• Provide enough room so that children may play on this unit safely. For
example, for structures with multiple play activities, a slide should not
exit in front of a swing.
• Place this unit where adults are easily able to watch children at play.
UNIT POSITIONING
RECOMMENDED SURFACING
IMPORTANT SAFETY INFORMATION
NOTE:
• DO NOT install loose ll surfacing over hard surfaces like concrete or
asphalt.
• Shredded bark mulch, wood chips, ne sand and ne gravel are added as
shock-absorbing materials after assembly. If used properly, these materials
can absorb some of the impact of a child’s fall.
• All surface material should extend a minimum of 6 ft. (2m) in all
directions around the play area.
• DO NOT apply surfacing materials until after the unit is completely
assembled and anchored.
• Create a play area free of obstacles that could cause injuries - such as
low-hanging tree branches, overhead wires, tree stumps or roots, large
rocks, bricks, and concrete.
• Do not build this unit on top of surfacing material.
• Locate bare metal platforms and slides out of direct sunlight to reduct the
likelihood of serious burns.
TIP: A slide that faces north will receive the least direct sunlight.
• Separate active and quiet activities from each other. For example, place
sandboxes away from swings, or use a separation guardrail or barrier.
• For to-fro swings, extend protective surfacing in front of and behind the
swing to a distance equal to twice the height of the top of the bar from
which the swing is suspended.
WARNING:
5’ 11” (1.8m)
6’1” (1.9m)
Minimum
14” (350mm)
69
Step 117:
Hammer (2) Ground Stakes (PC-HD23) into the ground next to the Beam Support Braces as shown.
Secure the Ground Stakes to the Beam Support Braces using (4) Screws (S119).
Step 118:
One week later check the Rope length on the Swings to make sure they are 14in (350mm) above the
ground. Make any necessary adjustments. Also, tighten all the hardware.
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for Little tikes 656200 Panther Peak at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of Little tikes 656200 Panther Peak in the language / languages: English as an attachment in your email.
The manual is 14.47 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
The manual is sent by email. Check your email
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.
