815242
3
Zoom out
Zoom in
Previous page
1/18
Next page
2
1. Position platform (L) to line up with corresponding letters on inside of each pillar (see reference 1).
2. Insert platform notch into the designated pillar and press down to secure.
1. Positionnez la plateforme (L) de manière à l’aligner avec les lettres correspondantes gurant sur le côté intérieur de chaque colonne (voir
référence n° 1).
2. Insérez l’encoche de la plateforme dans la colonne désignée et appuyez dessus pour une mise en place sécuritaire.
1. Coloque la plataforma (L) de manera que coincida con las letras correspondientes en el interior de cada pilar (ver referencia 1).
2. Inserte la muesca de la plataforma en el pilar correspondiente y empújela hacia abajo para asegurarla.
4
Install screw (Z) x3 into center of each pillar groove as shown.
Installez la vis (Z) x 3 dans le centre de la rainure de chaque colonne, comme illustré.
Fije 3 tornillos (Z) en el centro de la ranura de los 3 pilares tal y como se muestra.
x3
Z x3 - 2" (5.08 cm)
5
X x6 - 4" (10.16 cm)
x3
1
2
Person 1: MUST PRESS DOWN on
platform as screws are installed.
Person 2: Install screw (X) x2 per
pillar (6 total) into the locations
shown.
1re personne : VOUS DEVEZ
POUSSER SUR la plateforme pendant
que les vis sont installées.
2e personne : installez les vis (X) (2
vis par colonne; 6 vis au total) dans
les endroits illustrés.
Persona 1: DEBE EMPUJAR la plataforma
HACIA ABAJO mientras se jan los tornillos.
Persona 2: Fija 2 tornillos (X) por pilar
(un total de 6) en los lugares indicados.
3
2 people are required for this step. • Ces étapes requièrent deux personnes. • Se requieren 2 personas para estos paso.
Press Down
Pousser dessus
Empujar hacia
abajo
3
Each notch of the platform must be hammered down into its
designated pillar. Note: platform is in correct position once
notch is past bump in pillar as shown.
Chaque encoche de la plateforme doit être martelée pour l’insérer dans
la colonne qui lui est désignée. Remarque : la plateforme se trouve dans
la bonne position une fois que l’encoche passe à travers la bosse dans la
colonne, comme illustré.
Cada muesca de la plataforma debe martillarse en el pilar
correspondiente. Nota: La plataforma está en la posición correcta una vez
que la muesca haya pasado el saliente en el pilar tal y como se muestra.
Hammer past bump
Martelez l’encoche jusqu’à ce
qu’elle passe à travers la bosse
Martillar pasado el saliente
Screw should be tighten so that there is no gap larger than the
width of a screwdriver.
Les vis doivent être bien seres de sorte que le jeu ne soit pas plus grand
que la largeur dun tournevis.
Los tornillos deben ajustarse para que no quede un espacio mayor que el
ancho de un destornillador.
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Little tikes 631009M Endless Adventures Lookout Swing Set at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Little tikes 631009M Endless Adventures Lookout Swing Set in the language / languages: English, German, Dutch, French, Polish, Spanish as an attachment in your email.

The manual is 3.95 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info